Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Artesia as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Artesia, Los Angeles County, CA (90701)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What strike plate adjustment involves
- Who uses this service
- Signs you need strike plate adjustment service
- Strike Plate Adjustment across Artesia
- How our strike plate adjustment service works
- Typical calls we receive
- Equipment and hardware on the van
- Terms worth knowing
- Cost factors for strike plate adjustment service
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Doing it yourself versus calling a professional
- What we commit to
- How to choose a locksmith you can trust
- Before you call (562) 550-7206
- After the visit
- Related locksmith services in Artesia
- Strike Plate Adjustment near Artesia
- Strike Plate Adjustment in Artesia: frequently asked questions
What strike plate adjustment involves
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

If you have to lift, push or slam a door to get it to lock, something is out of line. For strike plate adjustment service in Artesia, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who uses this service
Door hardware calls in Artesia come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Artesia.
Signs you need strike plate adjustment service
If any of the following sounds familiar, strike plate adjustment service is likely what you need:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Artesia
Located in Los Angeles County, Artesia is an incorporated city within our Gateway Cities service area. We cover every part of Artesia, including the Pioneer Boulevard Little India district, the South Street corridor, and the Artesia Boulevard corridor. Wherever you are in town, the technician comes to your door, driveway or parking space. Service is available throughout ZIP code 90701.
Artesia is a small city known for the shops and restaurants of Little India, where jewelry and retail storefronts need high-security cylinders, gate locks and dependable safes.
If you are out and about near Little India on Pioneer Boulevard, Artesia Park, the Artesia Historical Museum, or the Artesia Towne Center, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Artesia follows SR-91, I-605, Pioneer Boulevard, Artesia Boulevard, South Street, and 183rd Street. You get a realistic arrival estimate when you call.
How our strike plate adjustment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
Cost factors for strike plate adjustment service
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Artesia.

Tips to avoid problems
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Get an itemized receipt showing labor, parts and the business details.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Artesia
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Artesia.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Mailbox Lock Replacement
Replacing mailbox locks when keys are lost, tenants move out or the lock is damaged.
- House Lockout
Unlocking front doors, back doors, side doors, garage entry doors and interior doors, without damaging the lock whenever possible.
Strike Plate Adjustment near Artesia
We provide the same strike plate adjustment service in the communities around Artesia. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Cerritos
- Strike Plate Adjustment in Bellflower
- Strike Plate Adjustment in Hawaiian Gardens
- Strike Plate Adjustment in Norwalk
- Strike Plate Adjustment in Lakewood
- Strike Plate Adjustment in Cypress
- Strike Plate Adjustment in Paramount
- Strike Plate Adjustment in Buena Park
- Strike Plate Adjustment in La Mirada
- Strike Plate Adjustment in Santa Fe Springs
- Strike Plate Adjustment in Downey
- Strike Plate Adjustment in Signal Hill
Strike Plate Adjustment in Artesia: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Artesia?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does it take a locksmith to reach me in Artesia?
It depends on where the nearest technician is and on traffic along SR-91, I-605, or Pioneer Boulevard. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Are you open 24 hours in Artesia?
Yes. We take calls and dispatch to Artesia 24 hours a day, including weekends and holidays.
Do you have a locksmith shop in Artesia?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Artesia and the rest of the Gateway Cities area. All work is done at your location.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
