Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Athens as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Athens, Los Angeles County, CA (90044, 90047)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What strike plate adjustment involves
- Who we help in Athens
- Signs you need strike plate adjustment service
- Strike Plate Adjustment across Athens
- Our strike plate adjustment process, step by step
- Common situations in Athens
- What our technicians bring
- A short glossary
- Cost factors for strike plate adjustment service
- What you can expect from us
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- What we commit to
- How to choose a locksmith you can trust
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Athens
- Strike Plate Adjustment near Athens
- Strike Plate Adjustment in Athens: frequently asked questions
What strike plate adjustment involves
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

If you have to lift, push or slam a door to get it to lock, something is out of line. For strike plate adjustment service in Athens, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who we help in Athens
Door hardware calls in Athens come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Athens.
Signs you need strike plate adjustment service
If any of the following sounds familiar, strike plate adjustment service is likely what you need:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Athens
Located in Los Angeles County, Athens is an unincorporated community within our Central & South Los Angeles service area. Customers anywhere in Athens, including West Athens, the Vermont Avenue corridor, the Western Avenue corridor, and the Imperial Highway corridor, can have a mobile technician sent directly to them. Service is available throughout ZIP codes 90044 and 90047.
Athens is an unincorporated residential community of single-family homes and small apartment buildings near the 105 and 110 interchange, where security door locks and car key replacements are frequent needs.
If you are out and about near Los Angeles Southwest College, Chester Washington Golf Course, Helen Keller Park, or the Vermont/Athens Metro station, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Athens follows I-105, I-110, Vermont Avenue, Western Avenue, Normandie Avenue, and Imperial Highway. You get a realistic arrival estimate when you call.
Our strike plate adjustment process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Athens
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The top corner of the door rubs the frame and the paint is wearing through.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Strike plate
- The plate on the frame that receives the latch or bolt.
Cost factors for strike plate adjustment service
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Athens.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.

Practical advice from our locksmiths
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Get an itemized receipt showing labor, parts and the business details.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Athens
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Athens.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
- Car Lockout
Unlocking vehicles when keys are locked inside.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
- Key Fob Replacement
Replacing remote key fobs for cars, trucks, SUVs and vans.
Strike Plate Adjustment near Athens
We provide the same strike plate adjustment service in the communities around Athens. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Westmont
- Strike Plate Adjustment in Gardena
- Strike Plate Adjustment in Willowbrook
- Strike Plate Adjustment in Hawthorne
- Strike Plate Adjustment in Lawndale
- Strike Plate Adjustment in Inglewood
- Strike Plate Adjustment in Compton
- Strike Plate Adjustment in Lynwood
- Strike Plate Adjustment in South Gate
- Strike Plate Adjustment in View Park–Windsor Hills
- Strike Plate Adjustment in Huntington Park
- Strike Plate Adjustment in Carson
Strike Plate Adjustment in Athens: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why do I have to push my door to lock it in Athens?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does it take a locksmith to reach me in Athens?
It depends on where the nearest technician is and on traffic along I-105, I-110, or Vermont Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of Athens do you serve?
All of Athens, including West Athens, the Vermont Avenue corridor, the Western Avenue corridor, and the Imperial Highway corridor, and addresses in ZIP codes 90044 and 90047.
Do you have a locksmith shop in Athens?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Athens and the rest of the Central & South Los Angeles area. All work is done at your location.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
