Quick answer
Door Guard Installation: Installing flip guards, swing guards or security latches. Big Daddy Car Key Replacement provides door guard installation service in Burbank as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Guard Installation
- Area
- Burbank, Los Angeles County, CA (91501, 91502, 91504, 91505, 91506)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What door guard installation means
- Customers we serve in Burbank
- Reasons to call for door guard installation service
- Door Guard Installation across Burbank
- What happens when you call
- Typical calls we receive
- Equipment and hardware on the van
- Terms worth knowing
- Cost factors for door guard installation service
- Why Burbank customers choose Big Daddy
- Tips to avoid problems
- Why this is a job for a locksmith
- Our service standards
- Questions to ask any locksmith
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Burbank
- Door Guard Installation near Burbank
- Door Guard Installation in Burbank: frequently asked questions
What door guard installation means
Installing flip guards, swing guards or security latches. Swing-bar guards, the type used on hotel doors, are sturdier than chains and easier to use. Flip locks mounted high on the frame also stop young children from opening doors. We install them into solid backing with long screws and position them clear of existing locks.

Doors in Burbank deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our door guard installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Burbank
Door hardware calls in Burbank come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Burbank.
Reasons to call for door guard installation service
These are the most common reasons customers in Burbank ask for door guard installation service:
- You want something stronger than a chain
- Small children can reach the door handle
- A family member tends to wander
- You want a night latch for extra reassurance
Door Guard Installation across Burbank
Located in Los Angeles County, Burbank is an incorporated city within our Burbank, Glendale & Foothills service area. We cover every part of Burbank, including Magnolia Park, the Media District, the Rancho Equestrian District, Downtown Burbank, and the Burbank Hills. Wherever you are in town, the technician comes to your door, driveway or parking space. Service is available throughout ZIP codes 91501, 91502, 91504, 91505, and 91506.
Burbank blends studio lots and media offices with tidy 1930s-to-1950s bungalows and hillside homes, so production-office master keys and vintage residential hardware are both familiar work.
If you are out and about near Warner Bros. Studios, Walt Disney Studios, Hollywood Burbank Airport, Burbank Town Center, or the Empire Center, give us that location when you call and wait somewhere safe and visible. Technicians usually reach Burbank by I-5, SR-134, Olive Avenue, Magnolia Boulevard, Burbank Boulevard, and Victory Boulevard. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- A latch has jammed and someone is stuck in a room.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The deadbolt only turns if you pull the door hard toward you.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for door guard installation service
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Burbank customers choose Big Daddy
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.

Tips to avoid problems
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Burbank
Customers who need door guard installation service often ask about these as well. Each can usually be handled in the same visit to Burbank.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Car Locksmith
On-site car key, lockout and ignition help wherever the vehicle is parked.
- Car Lockout
Unlocking vehicles when keys are locked inside.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
Door Guard Installation near Burbank
We provide the same door guard installation service in the communities around Burbank. See the main door guard installation page or the full list of service areas.
- Door Guard Installation in Toluca Lake
- Door Guard Installation in Glendale
- Door Guard Installation in North Hollywood
- Door Guard Installation in Sun Valley
- Door Guard Installation in Valley Village
- Door Guard Installation in Studio City
- Door Guard Installation in La Cañada Flintridge
- Door Guard Installation in Valley Glen
- Door Guard Installation in West Hollywood
- Door Guard Installation in Lake View Terrace
- Door Guard Installation in Van Nuys
- Door Guard Installation in Arleta
Door Guard Installation in Burbank: frequently asked questions
What is a swing bar door guard?
It is a hinged metal bar on the frame that swings over a post on the door, allowing it to open only a few inches. It is stronger than a chain and widely used on hotel room doors.
Why do I have to push my door to lock it in Burbank?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Do you have a locksmith shop in Burbank?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Burbank and the rest of the Burbank, Glendale & Foothills area. All work is done at your location.
How long does it take a locksmith to reach me in Burbank?
It depends on where the nearest technician is and on traffic along I-5, SR-134, or Olive Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Can you make car keys in Burbank?
Yes. We cut and program car keys on site anywhere in Burbank, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
