Quick answer
Latch Guard Installation: Installing latch guards to protect against forced entry. Big Daddy Car Key Replacement provides latch guard installation service in Carson as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Latch Guard Installation
- Area
- Carson, Los Angeles County, CA (90745, 90746, 90810)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our latch guard installation service
- Who we help in Carson
- When you need latch guard installation service
- Latch Guard Installation across Carson
- What happens when you call
- Common situations in Carson
- Equipment and hardware on the van
- A short glossary
- Cost factors for latch guard installation service
- What you can expect from us
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- What we commit to
- Choosing a locksmith: a short checklist
- What to have ready when you call
- After the visit
- Related locksmith services in Carson
- Latch Guard Installation near Carson
- Latch Guard Installation in Carson: frequently asked questions
About our latch guard installation service
Installing latch guards to protect against forced entry. A latch guard is a steel plate that covers the gap between door and frame at the lock, so a pry bar or credit card cannot reach the latch. It is essential on out-swinging doors, where the latch is otherwise exposed, and is a standard fitting on commercial back doors.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our latch guard installation service in Carson looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Who we help in Carson
Door hardware calls in Carson come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Carson.
When you need latch guard installation service
If any of the following sounds familiar, latch guard installation service is likely what you need:
- Your door swings outward
- Pry marks show at the latch
- The gap at the lock is wide enough to see the latch
- A back or side door is hidden from view
Latch Guard Installation across Carson
Carson is an incorporated city in Los Angeles County, part of the South Bay area we cover every day. Customers anywhere in Carson, including Dominguez Hills, the Avalon Boulevard corridor, the Carson Street corridor, and the industrial district near the 405, can have a mobile technician sent directly to them. That includes addresses in ZIP codes 90745, 90746, and 90810.
Carson is a logistics powerhouse near the ports, with warehouses, truck yards and refineries surrounding suburban neighborhoods, so fleet keys, semi-truck lockouts and commercial hardware are a big share of the work.
If you are out and about near Dignity Health Sports Park, California State University, Dominguez Hills, SouthBay Pavilion, or the Porsche Experience Center, give us that location when you call and wait somewhere safe and visible. Carson is served by I-405, I-110, SR-91, I-710, Avalon Boulevard, and Carson Street, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Common situations in Carson
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
- The door drifts open by itself because the latch no longer catches.
- The top corner of the door rubs the frame and the paint is wearing through.
- The deadbolt only turns if you pull the door hard toward you.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
Cost factors for latch guard installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Carson. The technician confirms the figure before starting.
What you can expect from us
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Carson.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.

Practical advice from our locksmiths
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Carson
Customers who need latch guard installation service often ask about these as well. Each can usually be handled in the same visit to Carson.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
- Safe Locksmith
Opening, repairing, servicing and changing combinations on home and business safes.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
Latch Guard Installation near Carson
We provide the same latch guard installation service in the communities around Carson. See the main latch guard installation page or the full list of service areas.
- Latch Guard Installation in West Carson
- Latch Guard Installation in Lomita
- Latch Guard Installation in Torrance
- Latch Guard Installation in Gardena
- Latch Guard Installation in Rolling Hills Estates
- Latch Guard Installation in Lawndale
- Latch Guard Installation in Compton
- Latch Guard Installation in Willowbrook
- Latch Guard Installation in Redondo Beach
- Latch Guard Installation in Athens
- Latch Guard Installation in Palos Verdes Estates
- Latch Guard Installation in Rolling Hills
Latch Guard Installation in Carson: frequently asked questions
What does a latch guard do?
It shields the latch and bolt from prying and shimming by covering the gap at the door edge. On out-swinging doors it is one of the most effective low-cost security additions.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Can you make car keys in Carson?
Yes. We cut and program car keys on site anywhere in Carson, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Are you open 24 hours in Carson?
Yes. We take calls and dispatch to Carson 24 hours a day, including weekends and holidays.
Which parts of Carson do you serve?
All of Carson, including Dominguez Hills, the Avalon Boulevard corridor, the Carson Street corridor, and the industrial district near the 405, and addresses in ZIP codes 90745, 90746, and 90810.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County and Ventura County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
