Quick answer
Latch Guard Installation: Installing latch guards to protect against forced entry. Big Daddy Car Key Replacement provides latch guard installation service in Huntington Park as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Latch Guard Installation
- Area
- Huntington Park, Los Angeles County, CA (90255)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What latch guard installation means
- Who uses this service
- Reasons to call for latch guard installation service
- Latch Guard Installation across Huntington Park
- Our latch guard installation process, step by step
- Common situations in Huntington Park
- Equipment and hardware on the van
- Trade terms explained
- What affects the cost of latch guard installation service
- What you can expect from us
- Practical advice from our locksmiths
- Professional service compared with doing it yourself
- Our service standards
- Questions to ask any locksmith
- What to have ready when you call
- After the visit
- Related locksmith services in Huntington Park
- Latch Guard Installation near Huntington Park
- Latch Guard Installation in Huntington Park: frequently asked questions
What latch guard installation means
Installing latch guards to protect against forced entry. A latch guard is a steel plate that covers the gap between door and frame at the lock, so a pry bar or credit card cannot reach the latch. It is essential on out-swinging doors, where the latch is otherwise exposed, and is a standard fitting on commercial back doors.

Doors in Huntington Park deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our latch guard installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who uses this service
Door hardware calls in Huntington Park come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Huntington Park.
Reasons to call for latch guard installation service
If any of the following sounds familiar, latch guard installation service is likely what you need:
- Your door swings outward
- Pry marks show at the latch
- The gap at the lock is wide enough to see the latch
- A back or side door is hidden from view
Latch Guard Installation across Huntington Park
Located in Los Angeles County, Huntington Park is an incorporated city within our Gateway Cities service area. Our latch guard installation service reaches all of Huntington Park, including the Pacific Boulevard shopping district, the Florence Avenue corridor, the Santa Fe Avenue corridor, and the Slauson industrial edge, as well as the streets in between. You do not need to bring anything to a shop. That includes addresses in ZIP code 90255.
Huntington Park’s Pacific Boulevard is one of the busiest shopping streets in Southeast Los Angeles, lined with storefronts that depend on roll-down gates, storefront locks and reliable rekeying.
If you are out and about near the Pacific Boulevard shopping district, Salt Lake Park, the Huntington Park Civic Center, or the historic Warner Theatre, give us that location when you call and wait somewhere safe and visible. Huntington Park is served by Pacific Boulevard, Florence Avenue, Slauson Avenue, Gage Avenue, Santa Fe Avenue, and Alameda Street, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
Our latch guard installation process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Huntington Park
- The deadbolt only turns if you pull the door hard toward you.
- The back door swings outward and its latch is visible through the gap.
- The door drifts open by itself because the latch no longer catches.
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
What affects the cost of latch guard installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Huntington Park.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.

Practical advice from our locksmiths
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Huntington Park
Customers who need latch guard installation service often ask about these as well. Each can usually be handled in the same visit to Huntington Park.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
- Automotive Locksmith
Mobile key, lock and ignition service for cars, trucks, SUVs, vans, motorcycles and fleets.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
Latch Guard Installation near Huntington Park
We provide the same latch guard installation service in the communities around Huntington Park. See the main latch guard installation page or the full list of service areas.
- Latch Guard Installation in Vernon
- Latch Guard Installation in South Gate
- Latch Guard Installation in Bell
- Latch Guard Installation in Maywood
- Latch Guard Installation in Cudahy
- Latch Guard Installation in Lynwood
- Latch Guard Installation in Commerce
- Latch Guard Installation in East Los Angeles
- Latch Guard Installation in Bell Gardens
- Latch Guard Installation in Willowbrook
- Latch Guard Installation in Westmont
- Latch Guard Installation in Athens
Latch Guard Installation in Huntington Park: frequently asked questions
What does a latch guard do?
It shields the latch and bolt from prying and shimming by covering the gap at the door edge. On out-swinging doors it is one of the most effective low-cost security additions.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Why do I have to push my door to lock it in Huntington Park?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Do you have a locksmith shop in Huntington Park?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Huntington Park and the rest of the Gateway Cities area. All work is done at your location.
Is there a travel charge for Huntington Park?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Huntington Park, so you know the cost in advance.
Are you open 24 hours in Huntington Park?
Yes. We take calls and dispatch to Huntington Park 24 hours a day, including weekends and holidays.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
