Quick answer
Door Alignment for Locks: Fixing lock issues caused by sagging doors, shifted frames or misalignment. Big Daddy Car Key Replacement provides door alignment service in Mission Hills as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Alignment for Locks
- Area
- Mission Hills, Los Angeles County, CA (91345)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our door alignment service
- Who we help in Mission Hills
- When you need door alignment service
- Door Alignment for Locks across Mission Hills
- How our door alignment service works
- Typical calls we receive
- Equipment and hardware on the van
- A short glossary
- How door alignment service is priced
- Why Mission Hills customers choose Big Daddy
- Practical advice from our locksmiths
- Professional service compared with doing it yourself
- Our service standards
- Questions to ask any locksmith
- Before you call (562) 550-7206
- Aftercare and records
- Related locksmith services in Mission Hills
- Door Alignment for Locks near Mission Hills
- Door Alignment for Locks in Mission Hills: frequently asked questions
About our door alignment service
Fixing lock issues caused by sagging doors, shifted frames or misalignment. When a house settles or a door swells in humid weather, the gap around the door changes and locks stop lining up. Realigning the door, by adjusting hinges, planing a tight edge or resetting the stop, cures the lock problem at its source instead of hacking the strike larger each year.

Doors in Mission Hills deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our door alignment service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who we help in Mission Hills
Door hardware calls in Mission Hills come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Mission Hills.
When you need door alignment service
These are the most common reasons customers in Mission Hills ask for door alignment service:
- Locks work in summer but not winter, or the reverse
- The gap around the door is uneven
- The door sticks at the top corner
- New locks were installed and still bind
Door Alignment for Locks across Mission Hills
Located in Los Angeles County, Mission Hills is a neighborhood of the City of Los Angeles within our San Fernando Valley service area. Customers anywhere in Mission Hills, including the San Fernando Mission district, the Sepulveda Boulevard corridor, and the Rinaldi Street corridor, can have a mobile technician sent directly to them. Service is available throughout ZIP code 91345.
Mission Hills sits where the 405, 5 and 118 meet, a neighborhood of 1950s tract homes and medical offices where commuters regularly need car lockout help and spare transponder keys.
People call us from all over Mission Hills, including the areas around Mission San Fernando Rey de España, Andrés Pico Adobe, Brand Park, and Providence Holy Cross Medical Center. A landmark or cross street helps the technician reach you quickly. Depending on where the closest technician is, the drive into Mission Hills follows I-405, I-5, SR-118, Sepulveda Boulevard, San Fernando Mission Boulevard, and Rinaldi Street. You get a realistic arrival estimate when you call.
How our door alignment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- The top corner of the door rubs the frame and the paint is wearing through.
- The back door swings outward and its latch is visible through the gap.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
How door alignment service is priced
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Mission Hills customers choose Big Daddy
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Mission Hills.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.

Practical advice from our locksmiths
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Get an itemized receipt showing labor, parts and the business details.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Mission Hills
Customers who need door alignment service often ask about these as well. Each can usually be handled in the same visit to Mission Hills.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Mobile Locksmith
A locksmith that comes directly to the customer’s location.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Commercial Door Hardware
Supplying and installing commercial-grade levers, pulls, hinges, closers, exit devices, strikes and protective plates.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
Door Alignment for Locks near Mission Hills
We provide the same door alignment service in the communities around Mission Hills. See the main door alignment for locks page or the full list of service areas.
- Door Alignment for Locks in North Hills
- Door Alignment for Locks in Arleta
- Door Alignment for Locks in Pacoima
- Door Alignment for Locks in San Fernando
- Door Alignment for Locks in Panorama City
- Door Alignment for Locks in Granada Hills
- Door Alignment for Locks in Sylmar
- Door Alignment for Locks in Lake Balboa
- Door Alignment for Locks in Northridge
- Door Alignment for Locks in Van Nuys
- Door Alignment for Locks in Valley Glen
- Door Alignment for Locks in Porter Ranch
Door Alignment for Locks in Mission Hills: frequently asked questions
Why does my lock only work at certain times of year?
Wood doors and frames swell with humidity and shrink when dry, shifting the bolt’s position relative to the strike. A proper alignment leaves enough clearance for seasonal movement.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Why do I have to push my door to lock it in Mission Hills?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Is there a travel charge for Mission Hills?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Mission Hills, so you know the cost in advance.
Do you have a locksmith shop in Mission Hills?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Mission Hills and the rest of the San Fernando Valley area. All work is done at your location.
Can you make car keys in Mission Hills?
Yes. We cut and program car keys on site anywhere in Mission Hills, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
