Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Orange as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Orange, Orange County, CA (92865, 92866, 92867, 92868, 92869)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What strike plate adjustment involves
- Customers we serve in Orange
- When you need strike plate adjustment service
- Strike Plate Adjustment across Orange
- What happens when you call
- Common situations in Orange
- What our technicians bring
- Terms worth knowing
- What affects the cost of strike plate adjustment service
- What you can expect from us
- Advice worth knowing
- Why this is a job for a locksmith
- What we commit to
- Questions to ask any locksmith
- What to have ready when you call
- Once the work is done
- Related locksmith services in Orange
- Strike Plate Adjustment near Orange
- Strike Plate Adjustment in Orange: frequently asked questions
What strike plate adjustment involves
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

Doors in Orange deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our strike plate adjustment service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Orange
Door hardware calls in Orange come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Orange.
When you need strike plate adjustment service
If any of the following sounds familiar, strike plate adjustment service is likely what you need:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Orange
Orange is an incorporated city in Orange County, part of the area we cover every day. Our strike plate adjustment service reaches all of Orange, including Old Towne Orange, the Chapman University area, El Modena, Orange Park Acres, Santiago Hills, and the area around The Outlets at Orange, as well as the streets in between. You do not need to bring anything to a shop. Service is available throughout ZIP codes 92865, 92866, 92867, 92868, and 92869.
Orange grew around Old Towne, roughly a square mile of pre-1940 homes and storefronts surrounding the Plaza, and now also takes in a university, a cluster of hospitals, newer hillside neighborhoods and the horse properties of Orange Park Acres, so antique mortise locks, student rentals, medical office hardware and gate locks all turn up.
If you are out and about near the Orange Plaza in Old Towne, Chapman University, The Outlets at Orange, UCI Medical Center, or Providence St. Joseph Hospital, give us that location when you call and wait somewhere safe and visible. Orange is served by SR-55, SR-57, SR-22, I-5, Chapman Avenue, and Katella Avenue, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Common situations in Orange
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
What affects the cost of strike plate adjustment service
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Orange. The technician confirms the figure before starting.
What you can expect from us
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Orange.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.

Advice worth knowing
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Questions to ask any locksmith
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Orange
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Orange.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Broken Key Extraction
Removing broken keys from door locks, deadbolts, mailbox locks, gates and other lock cylinders.
- Emergency Locksmith
Urgent lock and key help for homes, businesses and vehicles at any hour.
- Safe Locksmith
Opening, repairing, servicing and changing combinations on home and business safes.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
- Key Duplication
Making spare keys for house doors, gates, mailboxes, padlocks, cabinets and more.
Strike Plate Adjustment near Orange
We provide the same strike plate adjustment service in the communities around Orange. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Santa Ana
- Strike Plate Adjustment in Anaheim
- Strike Plate Adjustment in Garden Grove
- Strike Plate Adjustment in Placentia
- Strike Plate Adjustment in Fullerton
- Strike Plate Adjustment in Yorba Linda
- Strike Plate Adjustment in Stanton
- Strike Plate Adjustment in Buena Park
- Strike Plate Adjustment in Cypress
- Strike Plate Adjustment in La Mirada
- Strike Plate Adjustment in Hawaiian Gardens
- Strike Plate Adjustment in Cerritos
Strike Plate Adjustment in Orange: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Is there a travel charge for Orange?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Orange, so you know the cost in advance.
How long does it take a locksmith to reach me in Orange?
It depends on where the nearest technician is and on traffic along SR-55, SR-57, or SR-22. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of Orange do you serve?
All of Orange, including Old Towne Orange, the Chapman University area, El Modena, and Orange Park Acres, and addresses in ZIP codes 92865, 92866, 92867, 92868, and 92869.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
