Quick answer
Door Viewer & Peephole Installation: Installing peepholes or door viewers for added safety. Big Daddy Car Key Replacement provides peephole installation service in San Fernando as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Viewer & Peephole Installation
- Area
- San Fernando, Los Angeles County, CA (91340)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our peephole installation service
- Customers we serve in San Fernando
- Reasons to call for peephole installation service
- Door Viewer & Peephole Installation across San Fernando
- How our peephole installation service works
- Situations we handle regularly
- Equipment and hardware on the van
- Trade terms explained
- Cost factors for peephole installation service
- Why call Big Daddy Car Key Replacement
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- Our service standards
- Choosing a locksmith: a short checklist
- How to prepare for the visit
- Once the work is done
- Related locksmith services in San Fernando
- Door Viewer & Peephole Installation near San Fernando
- Door Viewer & Peephole Installation in San Fernando: frequently asked questions
About our peephole installation service
Installing peepholes or door viewers for added safety. A door viewer lets you see who is outside without opening the door. We install wide-angle viewers at the right height for the household, including a second lower viewer for children or wheelchair users, and can fit digital viewers that show the image on a small inside screen.

Doors in San Fernando deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our peephole installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in San Fernando
Door hardware calls in San Fernando come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in San Fernando.
Reasons to call for peephole installation service
These are the most common reasons customers in San Fernando ask for peephole installation service:
- Your front door has no way to see out
- The existing peephole is cloudy or too high
- A household member uses a wheelchair
- You want a wider field of view
Door Viewer & Peephole Installation across San Fernando
San Fernando is an incorporated city in Los Angeles County, part of the San Fernando Valley area we cover every day. Our peephole installation service reaches all of San Fernando, including the San Fernando Mall district, the Maclay Avenue corridor, the Truman Street corridor, and the residential blocks around Recreation Park, as well as the streets in between. You do not need to bring anything to a shop. We serve the 91340 ZIP code.
San Fernando is an independent city surrounded by Los Angeles, with a walkable historic downtown and early-1900s homes where storefront locks, security gates and older residential hardware are common jobs.
People call us from all over San Fernando, including the areas around the San Fernando Mall, the Lopez Adobe, the César E. Chávez Memorial, San Fernando Recreation Park, and the Sylmar/San Fernando Metrolink station. A landmark or cross street helps the technician reach you quickly. Technicians usually reach San Fernando by I-5, SR-118, I-210, I-405, San Fernando Road, and Maclay Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
How our peephole installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Situations we handle regularly
- The door drifts open by itself because the latch no longer catches.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- The back door swings outward and its latch is visible through the gap.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Strike plate
- The plate on the frame that receives the latch or bolt.
Cost factors for peephole installation service
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to San Fernando. The technician confirms the figure before starting.
Why call Big Daddy Car Key Replacement
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.

Practical advice from our locksmiths
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in San Fernando
Customers who need peephole installation service often ask about these as well. Each can usually be handled in the same visit to San Fernando.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Chain Installation
Installing door chains or secondary security locks.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Access Control Installation
Installing electronic access systems for offices, warehouses, apartment buildings and commercial facilities.
- House Lockout
Unlocking front doors, back doors, side doors, garage entry doors and interior doors, without damaging the lock whenever possible.
Door Viewer & Peephole Installation near San Fernando
We provide the same peephole installation service in the communities around San Fernando. See the main door viewer & peephole installation page or the full list of service areas.
- Door Viewer & Peephole Installation in Pacoima
- Door Viewer & Peephole Installation in Sylmar
- Door Viewer & Peephole Installation in Mission Hills
- Door Viewer & Peephole Installation in Arleta
- Door Viewer & Peephole Installation in Granada Hills
- Door Viewer & Peephole Installation in Panorama City
- Door Viewer & Peephole Installation in North Hills
- Door Viewer & Peephole Installation in Lake View Terrace
- Door Viewer & Peephole Installation in Sun Valley
- Door Viewer & Peephole Installation in Van Nuys
- Door Viewer & Peephole Installation in Valley Glen
- Door Viewer & Peephole Installation in Lake Balboa
Door Viewer & Peephole Installation in San Fernando: frequently asked questions
How high should a peephole be installed?
Standard height is around 58 to 60 inches from the floor, adjusted to the people who use the door. A second viewer around 43 inches suits children and seated users.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why do I have to push my door to lock it in San Fernando?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Do you have a locksmith shop in San Fernando?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout San Fernando and the rest of the San Fernando Valley area. All work is done at your location.
Is there a travel charge for San Fernando?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to San Fernando, so you know the cost in advance.
How long does it take a locksmith to reach me in San Fernando?
It depends on where the nearest technician is and on traffic along I-5, SR-118, or I-210. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
