Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in San Marino as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- San Marino, Los Angeles County, CA (91108)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What strike plate adjustment involves
- Who uses this service
- Reasons to call for strike plate adjustment service
- Strike Plate Adjustment across San Marino
- How our strike plate adjustment service works
- Typical calls we receive
- Equipment and hardware on the van
- Trade terms explained
- Cost factors for strike plate adjustment service
- Why call Big Daddy Car Key Replacement
- Practical advice from our locksmiths
- Doing it yourself versus calling a professional
- What we commit to
- How to choose a locksmith you can trust
- What to have ready when you call
- Once the work is done
- Related locksmith services in San Marino
- Strike Plate Adjustment near San Marino
- Strike Plate Adjustment in San Marino: frequently asked questions
What strike plate adjustment involves
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our strike plate adjustment service in San Marino looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Who uses this service
Door hardware calls in San Marino come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in San Marino.
Reasons to call for strike plate adjustment service
If any of the following sounds familiar, strike plate adjustment service is likely what you need:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across San Marino
Located in Los Angeles County, San Marino is an incorporated city within our San Gabriel Valley service area. We cover every part of San Marino, including the Huntington estate area, the Lacy Park area, the Huntington Drive corridor, and the Mission District edge. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 91108 ZIP code.
San Marino is an exclusively residential city of stately homes with strict design standards, where homeowners expect discreet service, high-security locks and careful work on original hardware.
If you are out and about near The Huntington Library, Art Museum and Botanical Gardens, Lacy Park, the Old Mill, or the Huntington Drive shops, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into San Marino follows Huntington Drive, Sierra Madre Boulevard, San Marino Avenue, Oxford Road, Los Robles Avenue, and Virginia Road. You get a realistic arrival estimate when you call.
How our strike plate adjustment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
Cost factors for strike plate adjustment service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.

Practical advice from our locksmiths
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in San Marino
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to San Marino.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Mobile Locksmith
A locksmith that comes directly to the customer’s location.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Mailbox Lock Replacement
Replacing mailbox locks when keys are lost, tenants move out or the lock is damaged.
- Transponder Key Programming
Programming chip keys for vehicles with immobilizer systems.
Strike Plate Adjustment near San Marino
We provide the same strike plate adjustment service in the communities around San Marino. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in San Gabriel
- Strike Plate Adjustment in Alhambra
- Strike Plate Adjustment in South Pasadena
- Strike Plate Adjustment in Pasadena
- Strike Plate Adjustment in Temple City
- Strike Plate Adjustment in Rosemead
- Strike Plate Adjustment in Sierra Madre
- Strike Plate Adjustment in Monterey Park
- Strike Plate Adjustment in Arcadia
- Strike Plate Adjustment in Altadena
- Strike Plate Adjustment in El Monte
- Strike Plate Adjustment in South El Monte
Strike Plate Adjustment in San Marino: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Why do I have to push my door to lock it in San Marino?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How long does it take a locksmith to reach me in San Marino?
It depends on where the nearest technician is and on traffic along Huntington Drive, Sierra Madre Boulevard, or San Marino Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of San Marino do you serve?
All of San Marino, including the Huntington estate area, the Lacy Park area, the Huntington Drive corridor, and the Mission District edge, and addresses in ZIP code 91108.
Are you open 24 hours in San Marino?
Yes. We take calls and dispatch to San Marino 24 hours a day, including weekends and holidays.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
