Quick answer
Door Hardware Repair: Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly. Big Daddy Car Key Replacement provides door hardware repair service in Sun Valley as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Hardware Repair
- Area
- Sun Valley, Los Angeles County, CA (91352)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our door hardware repair service
- Who we help in Sun Valley
- Signs you need door hardware repair service
- Door Hardware Repair across Sun Valley
- Our door hardware repair process, step by step
- Situations we handle regularly
- What our technicians bring
- Trade terms explained
- Cost factors for door hardware repair service
- What you can expect from us
- Advice worth knowing
- Professional service compared with doing it yourself
- Our service standards
- How to choose a locksmith you can trust
- What to have ready when you call
- Once the work is done
- Related locksmith services in Sun Valley
- Door Hardware Repair near Sun Valley
- Door Hardware Repair in Sun Valley: frequently asked questions
About our door hardware repair service
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly. A door that will not latch or lock is rarely a lock problem alone. Hinges loosen, frames shift and weatherstripping swells, and the hardware goes out of line. We look at the whole opening, fix the cause, and leave the door closing with a push and locking with two fingers.

Doors in Sun Valley deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our door hardware repair service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who we help in Sun Valley
Door hardware calls in Sun Valley come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
Our full list of locksmith services shows everything we offer, and the Sun Valley locksmith page covers local details.
Signs you need door hardware repair service
If any of the following sounds familiar, door hardware repair service is likely what you need:
- The door must be slammed or lifted to latch
- The deadbolt only works if you push on the door
- The door rubs the frame or floor
- Hardware is loose, rattling or misaligned
Door Hardware Repair across Sun Valley
Sun Valley is a neighborhood of the City of Los Angeles in Los Angeles County, part of the San Fernando Valley area we cover every day. We cover every part of Sun Valley, including the San Fernando Road industrial corridor, Stonehurst, the Sunland Boulevard corridor, and the Tuxford Street yards. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 91352 ZIP code.
Sun Valley is heavily industrial, with auto yards, recyclers and truck depots beside older homes and horse properties, so commercial padlocks, gate hardware, semi-truck keys and fleet work are routine.
If you are out and about near Hollywood Burbank Airport, the Theodore Payne Foundation, Stonehurst Recreation Center, or the auto dismantling and salvage yards, give us that location when you call and wait somewhere safe and visible. Technicians usually reach Sun Valley by I-5, SR-170, San Fernando Road, Glenoaks Boulevard, Sunland Boulevard, and Tuxford Street. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
Our door hardware repair process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Situations we handle regularly
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- A previous break-in left the jamb cracked around the strike.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
Cost factors for door hardware repair service
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Sun Valley. The technician confirms the figure before starting.
What you can expect from us
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.

Advice worth knowing
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
How to choose a locksmith you can trust
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Get an itemized receipt showing labor, parts and the business details.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Sun Valley
Customers who need door hardware repair service often ask about these as well. Each can usually be handled in the same visit to Sun Valley.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Mobile Locksmith
A locksmith that comes directly to the customer’s location.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
- Automotive Locksmith
Mobile key, lock and ignition service for cars, trucks, SUVs, vans, motorcycles and fleets.
- Storefront Lock Repair
Repairing locks on glass storefront doors, aluminum doors and commercial entryways.
- Safe Locksmith
Opening, repairing, servicing and changing combinations on home and business safes.
Door Hardware Repair near Sun Valley
We provide the same door hardware repair service in the communities around Sun Valley. See the main door hardware repair page or the full list of service areas.
- Door Hardware Repair in North Hollywood
- Door Hardware Repair in Valley Glen
- Door Hardware Repair in Lake View Terrace
- Door Hardware Repair in Valley Village
- Door Hardware Repair in Arleta
- Door Hardware Repair in Burbank
- Door Hardware Repair in Pacoima
- Door Hardware Repair in Panorama City
- Door Hardware Repair in Toluca Lake
- Door Hardware Repair in Van Nuys
- Door Hardware Repair in Studio City
- Door Hardware Repair in San Fernando
Door Hardware Repair in Sun Valley: frequently asked questions
Why does my door not latch anymore?
The latch and strike plate have moved out of alignment, most often because hinge screws have loosened and the door has dropped. Tightening or shimming the hinges and adjusting the strike restores the latch.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Why do I have to push my door to lock it in Sun Valley?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Is there a travel charge for Sun Valley?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Sun Valley, so you know the cost in advance.
Can you make car keys in Sun Valley?
Yes. We cut and program car keys on site anywhere in Sun Valley, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Are you open 24 hours in Sun Valley?
Yes. We take calls and dispatch to Sun Valley 24 hours a day, including weekends and holidays.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
