Quick answer
Door Alignment for Locks: Fixing lock issues caused by sagging doors, shifted frames or misalignment. Big Daddy Car Key Replacement provides door alignment service in Temple City as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Alignment for Locks
- Area
- Temple City, Los Angeles County, CA (91780)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our door alignment service
- Who we help in Temple City
- Reasons to call for door alignment service
- Door Alignment for Locks across Temple City
- How our door alignment service works
- Situations we handle regularly
- Tools, parts and hardware we carry
- A short glossary
- How door alignment service is priced
- Why call Big Daddy Car Key Replacement
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- How we work on every job
- Questions to ask any locksmith
- Before you call (562) 550-7206
- Once the work is done
- Related locksmith services in Temple City
- Door Alignment for Locks near Temple City
- Door Alignment for Locks in Temple City: frequently asked questions
About our door alignment service
Fixing lock issues caused by sagging doors, shifted frames or misalignment. When a house settles or a door swells in humid weather, the gap around the door changes and locks stop lining up. Realigning the door, by adjusting hinges, planing a tight edge or resetting the stop, cures the lock problem at its source instead of hacking the strike larger each year.

If you have to lift, push or slam a door to get it to lock, something is out of line. For door alignment service in Temple City, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who we help in Temple City
Door hardware calls in Temple City come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Temple City.
Reasons to call for door alignment service
If any of the following sounds familiar, door alignment service is likely what you need:
- Locks work in summer but not winter, or the reverse
- The gap around the door is uneven
- The door sticks at the top corner
- New locks were installed and still bind
Door Alignment for Locks across Temple City
Located in Los Angeles County, Temple City is an incorporated city within our San Gabriel Valley service area. Customers anywhere in Temple City, including the Las Tunas Drive downtown, the Rosemead Boulevard corridor, the Baldwin Avenue corridor, and the Longden corridor, can have a mobile technician sent directly to them. That includes addresses in ZIP code 91780.
Temple City is a quiet residential city where many older ranch homes are being rebuilt as large new houses, creating steady demand for new lock installation, keyed-alike hardware and smart deadbolts.
Whether you are at home, at work, or stuck near Temple City Park, Camellia Square, the Las Tunas Drive downtown, or Live Oak Park, tell the dispatcher the nearest landmark and we will find you. Depending on where the closest technician is, the drive into Temple City follows Rosemead Boulevard, Las Tunas Drive, Temple City Boulevard, Baldwin Avenue, Longden Avenue, and Lower Azusa Road. You get a realistic arrival estimate when you call.
How our door alignment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Situations we handle regularly
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
How door alignment service is priced
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Temple City.

Practical advice from our locksmiths
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Get an itemized receipt showing labor, parts and the business details.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Temple City
Customers who need door alignment service often ask about these as well. Each can usually be handled in the same visit to Temple City.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Car Locksmith
On-site car key, lockout and ignition help wherever the vehicle is parked.
- High Security Locks
Locks engineered to resist picking, bumping, drilling and unauthorized key copying.
- Mailbox Lock Replacement
Replacing mailbox locks when keys are lost, tenants move out or the lock is damaged.
- Access Control Installation
Installing electronic access systems for offices, warehouses, apartment buildings and commercial facilities.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
Door Alignment for Locks near Temple City
We provide the same door alignment service in the communities around Temple City. See the main door alignment for locks page or the full list of service areas.
- Door Alignment for Locks in Rosemead
- Door Alignment for Locks in Arcadia
- Door Alignment for Locks in San Gabriel
- Door Alignment for Locks in San Marino
- Door Alignment for Locks in El Monte
- Door Alignment for Locks in Sierra Madre
- Door Alignment for Locks in South El Monte
- Door Alignment for Locks in Alhambra
- Door Alignment for Locks in Monrovia
- Door Alignment for Locks in Monterey Park
- Door Alignment for Locks in Duarte
- Door Alignment for Locks in South Pasadena
Door Alignment for Locks in Temple City: frequently asked questions
Why does my lock only work at certain times of year?
Wood doors and frames swell with humidity and shrink when dry, shifting the bolt’s position relative to the strike. A proper alignment leaves enough clearance for seasonal movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why do I have to push my door to lock it in Temple City?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can you make car keys in Temple City?
Yes. We cut and program car keys on site anywhere in Temple City, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Which parts of Temple City do you serve?
All of Temple City, including the Las Tunas Drive downtown, the Rosemead Boulevard corridor, the Baldwin Avenue corridor, and the Longden corridor, and addresses in ZIP code 91780.
Do you have a locksmith shop in Temple City?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Temple City and the rest of the San Gabriel Valley area. All work is done at your location.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
