Quick answer
Exit Device Repair: Fixing commercial exit devices, dogging mechanisms, latches, rods and trim. Big Daddy Car Key Replacement provides exit device repair service in Ventura as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Exit Device Repair
- Area
- Ventura, Ventura County, CA (93001, 93003, 93004)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Commercial Locksmith Services
- Phone
- (562) 550-7206
On this page
- What exit device repair involves
- Customers we serve in Ventura
- Reasons to call for exit device repair service
- Exit Device Repair across Ventura
- Our exit device repair process, step by step
- Typical calls we receive
- What our technicians bring
- Trade terms explained
- How exit device repair service is priced
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Why this is a job for a locksmith
- Our service standards
- Questions to ask any locksmith
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Ventura
- Exit Device Repair near Ventura
- Exit Device Repair in Ventura: frequently asked questions
What exit device repair involves
Fixing commercial exit devices, dogging mechanisms, latches, rods and trim. Exit devices have many moving parts: touchpads, latchbolts, top and bottom rods, dogging cylinders and outside lever trim. Vertical rods go out of adjustment as doors sag, and bottom latches clog with debris. We adjust rods, replace worn latches and trim, and convert troublesome bottom rods to less-bottom-rod setups where permitted.

Every business in Ventura eventually faces the same questions. Who has keys? Do the exit doors work? Would the back door survive a pry bar? Our exit device repair service gives practical answers and carries out the work, usually in a single visit and with as little disruption as possible.
Customers we serve in Ventura
Our commercial customers in Ventura include retail shops, restaurants, offices, medical and dental practices, warehouses, schools, places of worship, property management companies and homeowners associations. Some need a one-time rekey after a staffing change, others an ongoing arrangement covering key systems, exit hardware and door maintenance across several sites.
This service is part of our commercial locksmith services in Ventura.
Reasons to call for exit device repair service
If any of the following sounds familiar, exit device repair service is likely what you need:
- Top or bottom rods do not engage
- The outside lever no longer opens the door
- The dogging key will not hold the bar down
- The device rattles or the end cap is missing
Exit Device Repair across Ventura
Located in Ventura County, Ventura is an incorporated city within our service area. Our exit device repair service reaches all of Ventura, including Downtown Ventura, Midtown, Pierpont, the Ventura Keys, the Westside Avenue district, East Ventura, Montalvo, and Saticoy, as well as the streets in between. You do not need to bring anything to a shop. We serve the 93001, 93003, and 93004 ZIP codes.
Ventura, officially San Buenaventura, is the county seat, with a mission-era downtown, beach cottages in Pierpont, boat docks in the Keys and county offices, so historic, marine and commercial lock work all meet here.
People call us from all over Ventura, including the areas around Mission San Buenaventura, the Ventura Pier and Promenade, Ventura Harbor Village, the Downtown Main Street district, and Grant Park and the Serra Cross. A landmark or cross street helps the technician reach you quickly. Depending on where the closest technician is, the drive into Ventura follows US-101, SR-126, SR-33, Main Street, Telegraph Road, and Victoria Avenue. You get a realistic arrival estimate when you call.
Our exit device repair process, step by step
Discuss the need and the site
We ask about the type of business, the doors involved and any deadline, such as an inspection, a tenant move-in or a termination. Photos of the doors help us arrive with the right parts.
Verify authority
Work on a commercial property is done for the owner, the tenant of record, or the property manager. We confirm that before any lock is opened or changed.
Survey the openings
Each door is checked for lock type and function, closer, hinges or pivots, exit hardware and fire rating, so the solution fits both the security need and the code.
Agree scope and price
You receive a clear scope: which doors, what hardware, how many keys, and the cost. For key systems we draft the hierarchy for your approval first.
Carry out the work around your schedule
Rekeys, repairs and installations are done before opening, after closing or during quiet hours when that suits the business better.
Test, document and hand over
Every door is tested for locking, latching and free exit. Keys are stamped and counted, and for master systems you receive a record of what opens what.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- Staff need access to the sales floor but not the office, stockroom or IT closet.
- A manager is let go and returns only some of the keys issued.
- The back door shows pry marks around the latch after the weekend.
- A fire inspection notes that the rear exit has a slide bolt and no panic hardware.
- The storefront door will not latch and the shop cannot be left for the night.
- A closer has failed and the front door slams hard enough to rattle the glass.
- You are taking over a suite and need the previous tenant’s keys cut off before move-in.
What our technicians bring
Commercial doors use purpose-built hardware. Aluminum storefronts typically carry Adams Rite-style deadlatches and hook bolts driven by a mortise cylinder. Hollow metal and wood doors use Grade 1 cylindrical levers or mortise locks from makers such as Schlage, Sargent, Corbin Russwin and Yale. Exits use panic and fire exit devices, and closers from LCN, Norton and similar makers control the swing. Interchangeable cores allow fast rekeying. We stock the common cylinders, cams, tailpieces, lock bodies and closers.
Trade terms explained
- Door closer
- A hydraulic device that closes a door at a controlled speed and holds it latched.
- Master key system
- A planned arrangement in which each lock has its own key and a master key opens all of them.
- Restricted keyway
- A key profile whose blanks are supplied only to authorized locksmiths, preventing unauthorized copies.
- Exit device
- Panic or fire exit hardware that unlatches a door when the horizontal bar is pushed.
- Cylindrical lock
- A lock installed through a round bore in the door, with the mechanism in the lever or knob assembly.
- Interchangeable core
- A removable lock core that a control key releases, allowing a door to be rekeyed in seconds.
- Mortise lock
- A heavy-duty lock housed in a pocket cut into the door edge, combining latch and deadbolt in one case.
- Lock function
- How a lock behaves, such as entry, storeroom, classroom or passage, which determines when it is locked and who can lock it.
How exit device repair service is priced
- Code and fire-rating requirements
- Fire-rated openings need listed hardware, and exits may need panic devices. Compliance can dictate the product.
- Hardware grade and function
- Grade 1 mortise locks and exit devices cost more than cylindrical levers, and they last far longer on busy doors.
- After-hours scheduling
- Work outside normal hours avoids disruption and may be priced differently. We quote both where it matters.
- Number and type of doors
- Aluminum storefront doors, hollow metal doors and wood office doors use different hardware. Pricing reflects how many openings are involved and what each requires.
- Restricted or high-security keys
- Patented keyways and high-security cylinders cost more per cylinder and per key, in exchange for real control over duplication.
- Electrified hardware
- Doors tied to access control, electric strikes or maglocks need wiring and coordination that add time.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Ventura.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.

Tips to avoid problems
- Give each employee access only to the doors their job requires.
- Never chain, padlock or bolt a required exit door while the building is occupied.
- Test exit devices and door closers monthly. A door that does not latch is an unlocked door.
- Consider keypad or card access for doors with frequent staff turnover.
- Use a restricted keyway if staff copying keys is a concern. A "Do Not Duplicate" stamp alone does not prevent copies.
- Have storefront pivots and closers serviced before the door starts dragging. It is cheaper than replacing a damaged lock.
- Keep a written key log: who holds which key, and the date it was issued and returned.
- Rekey whenever a keyholder leaves on poor terms or a key cannot be accounted for.
Why this is a job for a locksmith
Commercial doors are regulated in ways that homes are not. The wrong lock function can trap someone inside a storeroom, a deadbolt on an exit can fail an inspection or cost a life, and unlisted hardware can void a fire door’s rating. A commercial locksmith knows the functions, the grades and the applicable codes, keeps your key system mathematically sound, and documents the work so the next change is straightforward.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Ventura
Customers who need exit device repair service often ask about these as well. Each can usually be handled in the same visit to Ventura.
- IC Core Lock Systems
Installing and rekeying interchangeable core lock systems for commercial properties.
- Restricted Key Systems
Installing key systems that prevent unauthorized key duplication.
- Rim Cylinder Replacement
Replacing rim cylinders used with panic bars, exit devices and commercial doors.
- Commercial Lock Rekeying
Rekeying locks after employee turnover, lost keys, tenant changes or security concerns.
- Office Building Locksmith
Master key systems, access control, door hardware, lock repairs and tenant suite rekeys.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- File Cabinet Lock Replacement
Replacing locks on filing cabinets, desks and office storage.
- Panic Bar Repair
Repairing panic bars that stick, fail to latch, alarm or do not open correctly.
- Apartment Building Locksmith
Common area locks, unit rekeys, mailbox locks, access control, gate locks and emergency exit hardware.
- Commercial Lock Change
Replacing commercial-grade locks on offices, entry doors, back doors, storage rooms and restricted areas.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
- Ignition Repair
Repairing ignition cylinders that are stuck, worn or will not turn.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
- Automotive Locksmith
Mobile key, lock and ignition service for cars, trucks, SUVs, vans, motorcycles and fleets.
Exit Device Repair near Ventura
We provide the same exit device repair service in the communities around Ventura. See the main exit device repair page or the full list of service areas.
- Exit Device Repair in Oxnard
- Exit Device Repair in Port Hueneme
- Exit Device Repair in Santa Paula
- Exit Device Repair in Camarillo
- Exit Device Repair in Ojai
- Exit Device Repair in Fillmore
- Exit Device Repair in Moorpark
- Exit Device Repair in Thousand Oaks
- Exit Device Repair in Simi Valley
- Exit Device Repair in Westlake Village
- Exit Device Repair in Agoura Hills
- Exit Device Repair in Malibu
Exit Device Repair in Ventura: frequently asked questions
Can vertical rod exit devices be adjusted?
Yes. Rod length and latch engagement are adjustable, and most problems come from sagging doors pulling the rods out of range. We realign the door first and then set the rods so both latches engage fully.
How do we stop employees from copying keys?
Install a restricted key system. Its blanks are available only through the authorized locksmith and copies are cut only for people on your signature list.
Are our exit doors compliant?
We can check that exit doors open with one motion and no key, that panic hardware is present where required, and that closers latch the doors. Final authority rests with your fire marshal or building official.
Do you offer ongoing service for multiple locations?
Yes. We service multi-site businesses and managed properties across our service area and keep key records so later changes are fast.
Can you work outside our business hours in Ventura?
Yes. We are open 24 hours and regularly schedule rekeys, repairs and installations before opening or after closing so customers and staff are not disturbed.
What brands of commercial hardware do you service?
We work with the major commercial lines, including Schlage, Sargent, Corbin Russwin, Yale, Best, Adams Rite, Von Duprin, LCN, Norton and Kaba, and can match most existing hardware.
Can you provide documentation for our records?
Yes. For rekeys and key systems we provide a key schedule listing doors, key numbers and the quantity of keys issued.
Who is allowed to authorize lock changes for a business?
The owner, the tenant named on the lease, or the property manager. We verify authority before changing or opening any commercial lock.
Do you have a locksmith shop in Ventura?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Ventura and the surrounding communities. All work is done at your location.
Are you open 24 hours in Ventura?
Yes. We take calls and dispatch to Ventura 24 hours a day, including weekends and holidays.
Can you make car keys in Ventura?
Yes. We cut and program car keys on site anywhere in Ventura, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
