Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Glendale as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Glendale, Los Angeles County, CA (91201, 91202, 91203, 91204, 91205, 91206, 91207, 91208)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Customers we serve in Glendale
- When you need security strike plate installation service
- Security Strike Plate Installation across Glendale
- What happens when you call
- Typical calls we receive
- Tools, parts and hardware we carry
- Trade terms explained
- Cost factors for security strike plate installation service
- Why Glendale customers choose Big Daddy
- Tips to avoid problems
- Doing it yourself versus calling a professional
- Our service standards
- Questions to ask any locksmith
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Glendale
- Security Strike Plate Installation near Glendale
- Security Strike Plate Installation in Glendale: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our security strike plate installation service in Glendale looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Customers we serve in Glendale
Door hardware calls in Glendale come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Glendale.
When you need security strike plate installation service
People in Glendale usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Glendale
Glendale is an incorporated city in Los Angeles County, part of the Burbank, Glendale & Foothills area we cover every day. Customers anywhere in Glendale, including Downtown Glendale, Adams Hill, Rossmoyne, Verdugo Woodlands, Montrose, Sparr Heights, Glenoaks Canyon, and Chevy Chase Canyon, can have a mobile technician sent directly to them. That includes addresses in ZIP codes 91201, 91202, 91203, 91204, 91205, 91206, 91207, and 91208.
Glendale is one of the county’s largest cities, with high-rise offices and condos downtown, thousands of apartment units, and historic Spanish and Tudor homes in the hills, all with very different lock needs.
If you are out and about near The Americana at Brand, Glendale Galleria, Brand Library & Park, the Alex Theatre, or Glendale Community College, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Glendale follows SR-134, SR-2, I-5, Brand Boulevard, Colorado Street, and Glenoaks Boulevard. You get a realistic arrival estimate when you call.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for security strike plate installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Glendale. The technician confirms the figure before starting.
Why Glendale customers choose Big Daddy
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.

Tips to avoid problems
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Questions to ask any locksmith
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Glendale
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Glendale.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Lock Rekey
Changing the internal pins of an existing lock so old keys no longer work. Ideal after moving in, tenant changes, lost keys or employee turnover.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Car Key Replacement
Replacing lost, stolen or damaged car keys.
- House Lockout
Unlocking front doors, back doors, side doors, garage entry doors and interior doors, without damaging the lock whenever possible.
Security Strike Plate Installation near Glendale
We provide the same security strike plate installation service in the communities around Glendale. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Burbank
- Security Strike Plate Installation in La Cañada Flintridge
- Security Strike Plate Installation in Toluca Lake
- Security Strike Plate Installation in South Pasadena
- Security Strike Plate Installation in Pasadena
- Security Strike Plate Installation in West Hollywood
- Security Strike Plate Installation in Studio City
- Security Strike Plate Installation in Altadena
- Security Strike Plate Installation in North Hollywood
- Security Strike Plate Installation in Alhambra
- Security Strike Plate Installation in Valley Village
- Security Strike Plate Installation in Sun Valley
Security Strike Plate Installation in Glendale: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Glendale?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Do you have a locksmith shop in Glendale?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Glendale and the rest of the Burbank, Glendale & Foothills area. All work is done at your location.
Can you make car keys in Glendale?
Yes. We cut and program car keys on site anywhere in Glendale, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Is there a travel charge for Glendale?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Glendale, so you know the cost in advance.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County and Ventura County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
