Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Lomita as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Lomita, Los Angeles County, CA (90717)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation involves
- Who uses this service
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Lomita
- Our security strike plate installation process, step by step
- Typical calls we receive
- Tools, parts and hardware we carry
- Terms worth knowing
- What affects the cost of security strike plate installation service
- What you can expect from us
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- How we work on every job
- Choosing a locksmith: a short checklist
- How to prepare for the visit
- Aftercare and records
- Related locksmith services in Lomita
- Security Strike Plate Installation near Lomita
- Security Strike Plate Installation in Lomita: frequently asked questions
What security strike plate installation involves
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our security strike plate installation service in Lomita looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Who uses this service
Door hardware calls in Lomita come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Lomita.
Signs you need security strike plate installation service
If any of the following sounds familiar, security strike plate installation service is likely what you need:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Lomita
Lomita is an incorporated city in Los Angeles County, part of the South Bay area we cover every day. Customers anywhere in Lomita, including the Narbonne Avenue corridor, the Lomita Boulevard corridor, the Pacific Coast Highway corridor, and the hillside streets below Palos Verdes, can have a mobile technician sent directly to them. That includes addresses in ZIP code 90717.
Lomita is a small residential city at the foot of the Palos Verdes hills, with older single-family homes and small businesses that favor straightforward, durable lock repairs and rekeys.
Whether you are at home, at work, or stuck near the Lomita Railroad Museum, Lomita Park, the neighboring Zamperini Field, or the Pacific Coast Highway business strip, tell the dispatcher the nearest landmark and we will find you. Technicians usually reach Lomita by Pacific Coast Highway, Lomita Boulevard, Narbonne Avenue, Western Avenue, Crenshaw Boulevard, and Eshelman Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
Our security strike plate installation process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Typical calls we receive
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
What affects the cost of security strike plate installation service
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Lomita. The technician confirms the figure before starting.
What you can expect from us
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Lomita.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.

Practical advice from our locksmiths
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Lomita
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Lomita.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Smart Lock Installation
Installing smart locks, keypad locks, Wi-Fi locks, Bluetooth locks, app-controlled locks and keyless entry systems.
- High Security Locks
Locks engineered to resist picking, bumping, drilling and unauthorized key copying.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Safe Locksmith
Opening, repairing, servicing and changing combinations on home and business safes.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
Security Strike Plate Installation near Lomita
We provide the same security strike plate installation service in the communities around Lomita. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in West Carson
- Security Strike Plate Installation in Rolling Hills Estates
- Security Strike Plate Installation in Rolling Hills
- Security Strike Plate Installation in Carson
- Security Strike Plate Installation in Torrance
- Security Strike Plate Installation in Palos Verdes Estates
- Security Strike Plate Installation in Rancho Palos Verdes
- Security Strike Plate Installation in Redondo Beach
- Security Strike Plate Installation in Gardena
- Security Strike Plate Installation in Hermosa Beach
- Security Strike Plate Installation in Lawndale
- Security Strike Plate Installation in Long Beach
Security Strike Plate Installation in Lomita: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why do I have to push my door to lock it in Lomita?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does it take a locksmith to reach me in Lomita?
It depends on where the nearest technician is and on traffic along Pacific Coast Highway, Lomita Boulevard, or Narbonne Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Is there a travel charge for Lomita?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Lomita, so you know the cost in advance.
Are you open 24 hours in Lomita?
Yes. We take calls and dispatch to Lomita 24 hours a day, including weekends and holidays.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
