Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Long Beach as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Long Beach, Los Angeles County, CA (90802, 90803, 90804, 90805, 90806, 90807, 90808, 90810, 90813, 90814, 90815)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Customers we serve in Long Beach
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Long Beach
- What happens when you call
- Typical calls we receive
- Tools, parts and hardware we carry
- Terms worth knowing
- Cost factors for security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Professional service compared with doing it yourself
- What we commit to
- Choosing a locksmith: a short checklist
- Before you call (562) 550-7206
- Once the work is done
- Related locksmith services in Long Beach
- Security Strike Plate Installation near Long Beach
- Security Strike Plate Installation in Long Beach: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

If you have to lift, push or slam a door to get it to lock, something is out of line. For security strike plate installation service in Long Beach, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Customers we serve in Long Beach
Door hardware calls in Long Beach come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Long Beach.
Signs you need security strike plate installation service
These are the most common reasons customers in Long Beach ask for security strike plate installation service:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Long Beach
Long Beach is an incorporated city in Los Angeles County, part of the Gateway Cities area we cover every day. Our security strike plate installation service reaches all of Long Beach, including Downtown Long Beach, Belmont Shore, Naples, Bixby Knolls, Los Altos, California Heights, Alamitos Beach, Wrigley, North Long Beach, and the East Village, as well as the streets in between. You do not need to bring anything to a shop. We serve the 90802, 90803, 90804, 90805, 90806, 90807, 90808, 90810, 90813, 90814, and 90815 ZIP codes.
Long Beach is a full-scale city with a major port, high-rise downtown condos, Craftsman and Spanish bungalows, canal homes in Naples and thousands of boat slips, so every specialty from marine keys to historic hardware applies.
People call us from all over Long Beach, including the areas around the Queen Mary, the Aquarium of the Pacific, the Port of Long Beach, California State University, Long Beach, and Long Beach Airport. A landmark or cross street helps the technician reach you quickly. Technicians usually reach Long Beach by I-710, I-405, SR-91, I-605, SR-22, and Pacific Coast Highway. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Typical calls we receive
- The top corner of the door rubs the frame and the paint is wearing through.
- The back door swings outward and its latch is visible through the gap.
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
Cost factors for security strike plate installation service
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Long Beach. The technician confirms the figure before starting.
Why call Big Daddy Car Key Replacement
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.

Tips to avoid problems
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Long Beach
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Long Beach.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Key Fob Replacement
Replacing remote key fobs for cars, trucks, SUVs and vans.
- Locksmith Near Me
A local mobile locksmith dispatched to your location across Los Angeles, Ventura and Orange County.
- Storefront Lock Repair
Repairing locks on glass storefront doors, aluminum doors and commercial entryways.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
Security Strike Plate Installation near Long Beach
We provide the same security strike plate installation service in the communities around Long Beach. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Signal Hill
- Security Strike Plate Installation in Carson
- Security Strike Plate Installation in West Carson
- Security Strike Plate Installation in Lakewood
- Security Strike Plate Installation in Lomita
- Security Strike Plate Installation in Hawaiian Gardens
- Security Strike Plate Installation in Paramount
- Security Strike Plate Installation in Compton
- Security Strike Plate Installation in Bellflower
- Security Strike Plate Installation in Artesia
- Security Strike Plate Installation in Rolling Hills
- Security Strike Plate Installation in Rolling Hills Estates
Security Strike Plate Installation in Long Beach: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Are you open 24 hours in Long Beach?
Yes. We take calls and dispatch to Long Beach 24 hours a day, including weekends and holidays.
Is there a travel charge for Long Beach?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Long Beach, so you know the cost in advance.
Do you have a locksmith shop in Long Beach?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Long Beach and the rest of the Gateway Cities area. All work is done at your location.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
