Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Paramount as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Paramount, Los Angeles County, CA (90723)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Who we help in Paramount
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Paramount
- What happens when you call
- Common situations in Paramount
- What our technicians bring
- A short glossary
- What affects the cost of security strike plate installation service
- What you can expect from us
- Tips to avoid problems
- Why this is a job for a locksmith
- How we work on every job
- Questions to ask any locksmith
- What to have ready when you call
- Once the work is done
- Related locksmith services in Paramount
- Security Strike Plate Installation near Paramount
- Security Strike Plate Installation in Paramount: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

If you have to lift, push or slam a door to get it to lock, something is out of line. For security strike plate installation service in Paramount, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who we help in Paramount
Door hardware calls in Paramount come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Paramount.
Signs you need security strike plate installation service
If any of the following sounds familiar, security strike plate installation service is likely what you need:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Paramount
Located in Los Angeles County, Paramount is an incorporated city within our Gateway Cities service area. Our security strike plate installation service reaches all of Paramount, including the Paramount Boulevard corridor, the Somerset corridor, the industrial district along Garfield, and the Alondra corridor, as well as the streets in between. You do not need to bring anything to a shop. We serve the 90723 ZIP code.
Paramount mixes compact residential neighborhoods with metal shops, manufacturers and warehouses, so industrial padlocks, roll-up door locks and work-truck keys are as common as house calls.
People call us from all over Paramount, including the areas around the Paramount Swap Meet, Paramount Iceland, Paramount Park, and Progress Park. A landmark or cross street helps the technician reach you quickly. Depending on where the closest technician is, the drive into Paramount follows I-105, I-710, SR-91, Paramount Boulevard, Rosecrans Avenue, and Alondra Boulevard. You get a realistic arrival estimate when you call.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Paramount
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
- The door drifts open by itself because the latch no longer catches.
- The top corner of the door rubs the frame and the paint is wearing through.
- The deadbolt only turns if you pull the door hard toward you.
- A previous break-in left the jamb cracked around the strike.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
What affects the cost of security strike plate installation service
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Paramount.

Tips to avoid problems
- Out-swinging doors should have hinges with non-removable pins or security studs.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Paramount
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Paramount.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Mailbox Lock Replacement
Replacing mailbox locks when keys are lost, tenants move out or the lock is damaged.
- Master Key System
Creating a key hierarchy where owners, managers and employees have different levels of access.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Access Control Installation
Installing electronic access systems for offices, warehouses, apartment buildings and commercial facilities.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
Security Strike Plate Installation near Paramount
We provide the same security strike plate installation service in the communities around Paramount. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Bellflower
- Security Strike Plate Installation in Lakewood
- Security Strike Plate Installation in Compton
- Security Strike Plate Installation in Downey
- Security Strike Plate Installation in Lynwood
- Security Strike Plate Installation in Norwalk
- Security Strike Plate Installation in Artesia
- Security Strike Plate Installation in Cudahy
- Security Strike Plate Installation in Bell Gardens
- Security Strike Plate Installation in South Gate
- Security Strike Plate Installation in Willowbrook
- Security Strike Plate Installation in Santa Fe Springs
Security Strike Plate Installation in Paramount: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why do I have to push my door to lock it in Paramount?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Are you open 24 hours in Paramount?
Yes. We take calls and dispatch to Paramount 24 hours a day, including weekends and holidays.
Which parts of Paramount do you serve?
All of Paramount, including the Paramount Boulevard corridor, the Somerset corridor, the industrial district along Garfield, and the Alondra corridor, and addresses in ZIP code 90723.
How long does it take a locksmith to reach me in Paramount?
It depends on where the nearest technician is and on traffic along I-105, I-710, or SR-91. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County and Ventura County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
