Quick answer
Hinge Adjustment: Adjusting or replacing hinges so doors close correctly. Big Daddy Car Key Replacement provides hinge adjustment service in Santa Monica as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Hinge Adjustment
- Area
- Santa Monica, Los Angeles County, CA (90401, 90402, 90403, 90404, 90405)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What hinge adjustment means
- Customers we serve in Santa Monica
- Signs you need hinge adjustment service
- Hinge Adjustment across Santa Monica
- How our hinge adjustment service works
- Typical calls we receive
- Tools, parts and hardware we carry
- Trade terms explained
- What affects the cost of hinge adjustment service
- What you can expect from us
- Tips to avoid problems
- Why this is a job for a locksmith
- How we work on every job
- How to choose a locksmith you can trust
- Before you call (562) 550-7206
- After the visit
- Related locksmith services in Santa Monica
- Hinge Adjustment near Santa Monica
- Hinge Adjustment in Santa Monica: frequently asked questions
What hinge adjustment means
Adjusting or replacing hinges so doors close correctly. Hinges carry the full weight of the door. Stripped screw holes in the top hinge let the door sag toward the latch side, which is behind most latch and deadbolt complaints. We re-anchor hinges with long screws into the framing, shim or bend them into line, and replace worn hinges.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our hinge adjustment service in Santa Monica looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Customers we serve in Santa Monica
Door hardware calls in Santa Monica come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Santa Monica.
Signs you need hinge adjustment service
If any of the following sounds familiar, hinge adjustment service is likely what you need:
- The top hinge screws are loose or stripped
- The door has dropped at the latch side
- Hinges squeak, bind or show metal dust
- A heavy door is pulling away from the frame
Hinge Adjustment across Santa Monica
Located in Los Angeles County, Santa Monica is an incorporated city within our Westside service area. Our hinge adjustment service reaches all of Santa Monica, including Ocean Park, Sunset Park, the Pico District, Mid-City, Wilshire-Montana, North of Montana, and Downtown Santa Monica, as well as the streets in between. You do not need to bring anything to a shop. We serve the 90401, 90402, 90403, 90404, and 90405 ZIP codes.
Santa Monica is dense and coastal, with rent-controlled apartment buildings, beach condos, hotels and tech offices, where ocean air wears on hardware and parking-structure car lockouts are frequent.
Whether you are at home, at work, or stuck near Santa Monica Pier, Third Street Promenade, Santa Monica Place, Palisades Park, or Bergamot Station, tell the dispatcher the nearest landmark and we will find you. Depending on where the closest technician is, the drive into Santa Monica follows I-10, Pacific Coast Highway, Wilshire Boulevard, Santa Monica Boulevard, Pico Boulevard, and Ocean Avenue. You get a realistic arrival estimate when you call.
How our hinge adjustment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
What affects the cost of hinge adjustment service
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.

Tips to avoid problems
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Get an itemized receipt showing labor, parts and the business details.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Santa Monica
Customers who need hinge adjustment service often ask about these as well. Each can usually be handled in the same visit to Santa Monica.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Chain Installation
Installing door chains or secondary security locks.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Commercial Door Hardware
Supplying and installing commercial-grade levers, pulls, hinges, closers, exit devices, strikes and protective plates.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
- 24 Hour Locksmith
Locksmith help day or night, every day of the year.
- Master Key System
Creating a key hierarchy where owners, managers and employees have different levels of access.
Hinge Adjustment near Santa Monica
We provide the same hinge adjustment service in the communities around Santa Monica. See the main hinge adjustment page or the full list of service areas.
- Hinge Adjustment in Marina del Rey
- Hinge Adjustment in Culver City
- Hinge Adjustment in Beverly Hills
- Hinge Adjustment in Ladera Heights
- Hinge Adjustment in El Segundo
- Hinge Adjustment in Topanga
- Hinge Adjustment in View Park–Windsor Hills
- Hinge Adjustment in Inglewood
- Hinge Adjustment in West Hollywood
- Hinge Adjustment in Sherman Oaks
- Hinge Adjustment in Encino
- Hinge Adjustment in Studio City
Hinge Adjustment in Santa Monica: frequently asked questions
Can loose hinges cause lock problems?
Yes, it is the most common cause. A sagging door moves the latch and bolt downward so they no longer meet the strike. Securing the hinges often fixes the lock without touching it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why do I have to push my door to lock it in Santa Monica?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Is there a travel charge for Santa Monica?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Santa Monica, so you know the cost in advance.
Can you make car keys in Santa Monica?
Yes. We cut and program car keys on site anywhere in Santa Monica, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Which parts of Santa Monica do you serve?
All of Santa Monica, including Ocean Park, Sunset Park, the Pico District, and Mid-City, and addresses in ZIP codes 90401, 90402, 90403, 90404, and 90405.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
