Quick answer
Door Hardware Repair: Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly. Big Daddy Car Key Replacement provides door hardware repair service in Santa Monica as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Door Hardware Repair
- Area
- Santa Monica, Los Angeles County, CA (90401, 90402, 90403, 90404, 90405)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What door hardware repair means
- Who we help in Santa Monica
- Reasons to call for door hardware repair service
- Door Hardware Repair across Santa Monica
- Our door hardware repair process, step by step
- Typical calls we receive
- Tools, parts and hardware we carry
- A short glossary
- What affects the cost of door hardware repair service
- Why call Big Daddy Car Key Replacement
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- How we work on every job
- Questions to ask any locksmith
- What to have ready when you call
- Once the work is done
- Related locksmith services in Santa Monica
- Door Hardware Repair near Santa Monica
- Door Hardware Repair in Santa Monica: frequently asked questions
What door hardware repair means
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly. A door that will not latch or lock is rarely a lock problem alone. Hinges loosen, frames shift and weatherstripping swells, and the hardware goes out of line. We look at the whole opening, fix the cause, and leave the door closing with a push and locking with two fingers.

If you have to lift, push or slam a door to get it to lock, something is out of line. For door hardware repair service in Santa Monica, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who we help in Santa Monica
Door hardware calls in Santa Monica come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
Our full list of locksmith services shows everything we offer, and the Santa Monica locksmith page covers local details.
Reasons to call for door hardware repair service
If any of the following sounds familiar, door hardware repair service is likely what you need:
- The door must be slammed or lifted to latch
- The deadbolt only works if you push on the door
- The door rubs the frame or floor
- Hardware is loose, rattling or misaligned
Door Hardware Repair across Santa Monica
Located in Los Angeles County, Santa Monica is an incorporated city within our Westside service area. Customers anywhere in Santa Monica, including Ocean Park, Sunset Park, the Pico District, Mid-City, Wilshire-Montana, North of Montana, and Downtown Santa Monica, can have a mobile technician sent directly to them. That includes addresses in ZIP codes 90401, 90402, 90403, 90404, and 90405.
Santa Monica is dense and coastal, with rent-controlled apartment buildings, beach condos, hotels and tech offices, where ocean air wears on hardware and parking-structure car lockouts are frequent.
Whether you are at home, at work, or stuck near Santa Monica Pier, Third Street Promenade, Santa Monica Place, Palisades Park, or Bergamot Station, tell the dispatcher the nearest landmark and we will find you. Technicians usually reach Santa Monica by I-10, Pacific Coast Highway, Wilshire Boulevard, Santa Monica Boulevard, Pico Boulevard, and Ocean Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
Our door hardware repair process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- A latch has jammed and someone is stuck in a room.
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
What affects the cost of door hardware repair service
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Santa Monica.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.

Practical advice from our locksmiths
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Santa Monica
Customers who need door hardware repair service often ask about these as well. Each can usually be handled in the same visit to Santa Monica.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
Door Hardware Repair near Santa Monica
We provide the same door hardware repair service in the communities around Santa Monica. See the main door hardware repair page or the full list of service areas.
- Door Hardware Repair in Marina del Rey
- Door Hardware Repair in Culver City
- Door Hardware Repair in Beverly Hills
- Door Hardware Repair in Ladera Heights
- Door Hardware Repair in El Segundo
- Door Hardware Repair in Topanga
- Door Hardware Repair in View Park–Windsor Hills
- Door Hardware Repair in Inglewood
- Door Hardware Repair in West Hollywood
- Door Hardware Repair in Sherman Oaks
- Door Hardware Repair in Encino
- Door Hardware Repair in Studio City
Door Hardware Repair in Santa Monica: frequently asked questions
Why does my door not latch anymore?
The latch and strike plate have moved out of alignment, most often because hinge screws have loosened and the door has dropped. Tightening or shimming the hinges and adjusting the strike restores the latch.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why do I have to push my door to lock it in Santa Monica?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How long does it take a locksmith to reach me in Santa Monica?
It depends on where the nearest technician is and on traffic along I-10, Pacific Coast Highway, or Wilshire Boulevard. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Do you have a locksmith shop in Santa Monica?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Santa Monica and the rest of the Westside area. All work is done at your location.
Can you make car keys in Santa Monica?
Yes. We cut and program car keys on site anywhere in Santa Monica, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
