Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Sylmar as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Sylmar, Los Angeles County, CA (91342)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Who we help in Sylmar
- When you need security strike plate installation service
- Security Strike Plate Installation across Sylmar
- What happens when you call
- Common situations in Sylmar
- What our technicians bring
- A short glossary
- Cost factors for security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Advice worth knowing
- Why this is a job for a locksmith
- What we commit to
- How to choose a locksmith you can trust
- Before you call (562) 550-7206
- Once the work is done
- Related locksmith services in Sylmar
- Security Strike Plate Installation near Sylmar
- Security Strike Plate Installation in Sylmar: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Sylmar deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who we help in Sylmar
Door hardware calls in Sylmar come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Sylmar.
When you need security strike plate installation service
If any of the following sounds familiar, security strike plate installation service is likely what you need:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Sylmar
Sylmar is a neighborhood of the City of Los Angeles in Los Angeles County, part of the San Fernando Valley area we cover every day. Our security strike plate installation service reaches all of Sylmar, including the Foothill Boulevard corridor, the Olive View area, the equestrian lots near El Cariso, and the Hubbard Street corridor, as well as the streets in between. You do not need to bring anything to a shop. That includes addresses in ZIP code 91342.
Sylmar is the northernmost neighborhood in Los Angeles, with large lots, manufactured-home communities and newer tract developments, plus several freeway interchanges where stranded drivers call for lockouts and lost keys.
If you are out and about near Olive View–UCLA Medical Center, Los Angeles Mission College, El Cariso Community Regional Park, or the Nethercutt Museum, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Sylmar follows I-5, I-210, SR-118, I-405, Foothill Boulevard, and Glenoaks Boulevard. You get a realistic arrival estimate when you call.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Common situations in Sylmar
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for security strike plate installation service
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Sylmar. The technician confirms the figure before starting.
Why call Big Daddy Car Key Replacement
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Sylmar.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.

Advice worth knowing
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
How to choose a locksmith you can trust
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Sylmar
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Sylmar.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
- Broken Key Extraction
Removing broken keys from door locks, deadbolts, mailbox locks, gates and other lock cylinders.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Mailbox Lock Replacement
Replacing mailbox locks when keys are lost, tenants move out or the lock is damaged.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
Security Strike Plate Installation near Sylmar
We provide the same security strike plate installation service in the communities around Sylmar. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in San Fernando
- Security Strike Plate Installation in Pacoima
- Security Strike Plate Installation in Granada Hills
- Security Strike Plate Installation in Mission Hills
- Security Strike Plate Installation in Arleta
- Security Strike Plate Installation in Lake View Terrace
- Security Strike Plate Installation in North Hills
- Security Strike Plate Installation in Panorama City
- Security Strike Plate Installation in Porter Ranch
- Security Strike Plate Installation in Northridge
- Security Strike Plate Installation in Sun Valley
- Security Strike Plate Installation in Santa Clarita
Security Strike Plate Installation in Sylmar: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why do I have to push my door to lock it in Sylmar?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Is there a travel charge for Sylmar?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Sylmar, so you know the cost in advance.
How long does it take a locksmith to reach me in Sylmar?
It depends on where the nearest technician is and on traffic along I-5, I-210, or SR-118. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of Sylmar do you serve?
All of Sylmar, including the Foothill Boulevard corridor, the Olive View area, the equestrian lots near El Cariso, and the Hubbard Street corridor, and addresses in ZIP code 91342.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
