Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Porter Ranch as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Porter Ranch, Los Angeles County, CA (91326)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Customers we serve in Porter Ranch
- When you need security strike plate installation service
- Security Strike Plate Installation across Porter Ranch
- What happens when you call
- Common situations in Porter Ranch
- Equipment and hardware on the van
- Terms worth knowing
- Cost factors for security strike plate installation service
- Why Porter Ranch customers choose Big Daddy
- Advice worth knowing
- Doing it yourself versus calling a professional
- How we work on every job
- How to choose a locksmith you can trust
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Porter Ranch
- Security Strike Plate Installation near Porter Ranch
- Security Strike Plate Installation in Porter Ranch: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

If you have to lift, push or slam a door to get it to lock, something is out of line. For security strike plate installation service in Porter Ranch, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Customers we serve in Porter Ranch
Door hardware calls in Porter Ranch come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Porter Ranch.
When you need security strike plate installation service
These are the most common reasons customers in Porter Ranch ask for security strike plate installation service:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Porter Ranch
Located in Los Angeles County, Porter Ranch is a neighborhood of the City of Los Angeles within our San Fernando Valley service area. Customers anywhere in Porter Ranch, including Porter Ranch Estates, Renaissance, The Canyons, Westcliffe, and Bella Vista, can have a mobile technician sent directly to them. That includes addresses in ZIP code 91326.
Porter Ranch is one of the newest parts of the Valley, with gated communities and builder-grade hardware that homeowners often upgrade to smart locks, keypad deadbolts and reinforced strike plates.
People call us from all over Porter Ranch, including the areas around The Vineyards at Porter Ranch, Porter Ranch Town Center, Aliso Canyon Park, Limekiln Canyon Park, and Holleigh Bernson Memorial Park. A landmark or cross street helps the technician reach you quickly. Technicians usually reach Porter Ranch by SR-118, Rinaldi Street, Tampa Avenue, Porter Ranch Drive, Mason Avenue, and Sesnon Boulevard. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Porter Ranch
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
Cost factors for security strike plate installation service
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Porter Ranch customers choose Big Daddy
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Porter Ranch.

Advice worth knowing
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Out-swinging doors should have hinges with non-removable pins or security studs.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Porter Ranch
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Porter Ranch.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
- Deadbolt Installation
Installing single-cylinder, double-cylinder, high-security or smart deadbolts.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Commercial Door Hardware
Supplying and installing commercial-grade levers, pulls, hinges, closers, exit devices, strikes and protective plates.
Security Strike Plate Installation near Porter Ranch
We provide the same security strike plate installation service in the communities around Porter Ranch. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Granada Hills
- Security Strike Plate Installation in Chatsworth
- Security Strike Plate Installation in Northridge
- Security Strike Plate Installation in Winnetka
- Security Strike Plate Installation in North Hills
- Security Strike Plate Installation in Mission Hills
- Security Strike Plate Installation in Reseda
- Security Strike Plate Installation in Canoga Park
- Security Strike Plate Installation in Sylmar
- Security Strike Plate Installation in Lake Balboa
- Security Strike Plate Installation in San Fernando
- Security Strike Plate Installation in Panorama City
Security Strike Plate Installation in Porter Ranch: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Porter Ranch?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Can you make car keys in Porter Ranch?
Yes. We cut and program car keys on site anywhere in Porter Ranch, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Is there a travel charge for Porter Ranch?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Porter Ranch, so you know the cost in advance.
Do you have a locksmith shop in Porter Ranch?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Porter Ranch and the rest of the San Fernando Valley area. All work is done at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
