Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Reseda as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Reseda, Los Angeles County, CA (91335)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Customers we serve in Reseda
- When you need security strike plate installation service
- Security Strike Plate Installation across Reseda
- What happens when you call
- Typical calls we receive
- Equipment and hardware on the van
- Terms worth knowing
- Cost factors for security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Why this is a job for a locksmith
- Our service standards
- Choosing a locksmith: a short checklist
- What to have ready when you call
- Aftercare and records
- Related locksmith services in Reseda
- Security Strike Plate Installation near Reseda
- Security Strike Plate Installation in Reseda: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Reseda deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Reseda
Door hardware calls in Reseda come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Reseda.
When you need security strike plate installation service
People in Reseda usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Reseda
Reseda is a neighborhood of the City of Los Angeles in Los Angeles County, part of the San Fernando Valley area we cover every day. Customers anywhere in Reseda, including the Sherman Way commercial strip, the Reseda Boulevard corridor, and the blocks around Reseda Park, can have a mobile technician sent directly to them. Service is available throughout ZIP code 91335.
Reseda is a classic Valley grid of 1950s tract houses, garden apartments and strip-mall storefronts, where worn-out original locks, storefront cylinders and older ignition problems are common calls.
People call us from all over Reseda, including the areas around Reseda Park, the Sherman Way business district, the historic Reseda Theatre, and the Los Angeles River greenway. A landmark or cross street helps the technician reach you quickly. Technicians usually reach Reseda by US-101, Reseda Boulevard, Sherman Way, Victory Boulevard, Vanowen Street, and Tampa Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Typical calls we receive
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- The back door swings outward and its latch is visible through the gap.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- The door drifts open by itself because the latch no longer catches.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for security strike plate installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Reseda. The technician confirms the figure before starting.
Why call Big Daddy Car Key Replacement
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Reseda.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.

Tips to avoid problems
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Reseda
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Reseda.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Panic Bar Installation
Installing panic bars, push bars and crash bars for emergency exits.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
- Lock Rekey
Changing the internal pins of an existing lock so old keys no longer work. Ideal after moving in, tenant changes, lost keys or employee turnover.
- Locksmith Near Me
A local mobile locksmith dispatched to your location across Los Angeles County and Ventura County.
Security Strike Plate Installation near Reseda
We provide the same security strike plate installation service in the communities around Reseda. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Northridge
- Security Strike Plate Installation in Lake Balboa
- Security Strike Plate Installation in Winnetka
- Security Strike Plate Installation in Tarzana
- Security Strike Plate Installation in Canoga Park
- Security Strike Plate Installation in Encino
- Security Strike Plate Installation in North Hills
- Security Strike Plate Installation in Woodland Hills
- Security Strike Plate Installation in Van Nuys
- Security Strike Plate Installation in Panorama City
- Security Strike Plate Installation in Chatsworth
- Security Strike Plate Installation in Mission Hills
Security Strike Plate Installation in Reseda: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why do I have to push my door to lock it in Reseda?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Is there a travel charge for Reseda?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Reseda, so you know the cost in advance.
How long does it take a locksmith to reach me in Reseda?
It depends on where the nearest technician is and on traffic along US-101, Reseda Boulevard, or Sherman Way. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Are you open 24 hours in Reseda?
Yes. We take calls and dispatch to Reseda 24 hours a day, including weekends and holidays.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
