Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Van Nuys as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Van Nuys, Los Angeles County, CA (91401, 91405, 91406, 91411)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation involves
- Customers we serve in Van Nuys
- When you need security strike plate installation service
- Security Strike Plate Installation across Van Nuys
- How our security strike plate installation service works
- Typical calls we receive
- Tools, parts and hardware we carry
- Trade terms explained
- How security strike plate installation service is priced
- What you can expect from us
- Tips to avoid problems
- Why this is a job for a locksmith
- How we work on every job
- Choosing a locksmith: a short checklist
- Before you call (562) 550-7206
- Once the work is done
- Related locksmith services in Van Nuys
- Security Strike Plate Installation near Van Nuys
- Security Strike Plate Installation in Van Nuys: frequently asked questions
What security strike plate installation involves
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our security strike plate installation service in Van Nuys looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Customers we serve in Van Nuys
Door hardware calls in Van Nuys come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Van Nuys.
When you need security strike plate installation service
People in Van Nuys usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Van Nuys
Located in Los Angeles County, Van Nuys is a neighborhood of the City of Los Angeles within our San Fernando Valley service area. Our security strike plate installation service reaches all of Van Nuys, including the Van Nuys Civic Center, the Van Nuys Boulevard auto row, the Sepulveda corridor, and the Van Nuys Airport business district, as well as the streets in between. You do not need to bring anything to a shop. That includes addresses in ZIP codes 91401, 91405, 91406, and 91411.
Van Nuys is the civic and commercial heart of the Valley, with 1940s bungalows, dense apartment corridors, auto dealerships and airport-area warehouses generating every kind of locksmith call.
Whether you are at home, at work, or stuck near the Van Nuys Civic Center, Van Nuys Airport, the Van Nuys Courthouse, or the Metro G Line busway, tell the dispatcher the nearest landmark and we will find you. Depending on where the closest technician is, the drive into Van Nuys follows I-405, US-101, Van Nuys Boulevard, Sepulveda Boulevard, Victory Boulevard, and Sherman Way. You get a realistic arrival estimate when you call.
How our security strike plate installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
How security strike plate installation service is priced
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.

Tips to avoid problems
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Choosing a locksmith: a short checklist
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Get an itemized receipt showing labor, parts and the business details.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Van Nuys
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Van Nuys.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Emergency Locksmith
Urgent lock and key help for homes, businesses and vehicles at any hour.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
- Locksmith Near Me
A local mobile locksmith dispatched to your location across Los Angeles County and Ventura County.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Key Fob Replacement
Replacing remote key fobs for cars, trucks, SUVs and vans.
Security Strike Plate Installation near Van Nuys
We provide the same security strike plate installation service in the communities around Van Nuys. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Valley Glen
- Security Strike Plate Installation in Panorama City
- Security Strike Plate Installation in Sherman Oaks
- Security Strike Plate Installation in Lake Balboa
- Security Strike Plate Installation in Encino
- Security Strike Plate Installation in Valley Village
- Security Strike Plate Installation in North Hills
- Security Strike Plate Installation in Arleta
- Security Strike Plate Installation in North Hollywood
- Security Strike Plate Installation in Mission Hills
- Security Strike Plate Installation in Reseda
- Security Strike Plate Installation in Sun Valley
Security Strike Plate Installation in Van Nuys: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why do I have to push my door to lock it in Van Nuys?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Are you open 24 hours in Van Nuys?
Yes. We take calls and dispatch to Van Nuys 24 hours a day, including weekends and holidays.
Is there a travel charge for Van Nuys?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Van Nuys, so you know the cost in advance.
How long does it take a locksmith to reach me in Van Nuys?
It depends on where the nearest technician is and on traffic along I-405, US-101, or Van Nuys Boulevard. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
