Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Arcadia as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Arcadia, Los Angeles County, CA (91006, 91007)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation involves
- Who we help in Arcadia
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Arcadia
- Our security strike plate installation process, step by step
- Typical calls we receive
- Equipment and hardware on the van
- A short glossary
- How security strike plate installation service is priced
- What you can expect from us
- Practical advice from our locksmiths
- Doing it yourself versus calling a professional
- How we work on every job
- How to choose a locksmith you can trust
- What to have ready when you call
- Once the work is done
- Related locksmith services in Arcadia
- Security Strike Plate Installation near Arcadia
- Security Strike Plate Installation in Arcadia: frequently asked questions
What security strike plate installation involves
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our security strike plate installation service in Arcadia looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Who we help in Arcadia
Door hardware calls in Arcadia come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Arcadia.
Signs you need security strike plate installation service
People in Arcadia usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Arcadia
Located in Los Angeles County, Arcadia is an incorporated city within our San Gabriel Valley service area. We cover every part of Arcadia, including the Upper Rancho, the Lower Rancho, Santa Anita Oaks, the Baldwin Avenue corridor, and Downtown Arcadia. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 91006 and 91007 ZIP codes.
Arcadia is known for large custom homes, many newly built, where owners want multi-point locks, high-security cylinders, safes and smart entry systems installed correctly the first time.
Whether you are at home, at work, or stuck near Santa Anita Park, The Shops at Santa Anita, the Los Angeles County Arboretum, or Arcadia County Park, tell the dispatcher the nearest landmark and we will find you. Arcadia is served by I-210, Huntington Drive, Baldwin Avenue, Santa Anita Avenue, Foothill Boulevard, and Duarte Road, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
Our security strike plate installation process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
How security strike plate installation service is priced
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Arcadia.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.

Practical advice from our locksmiths
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Out-swinging doors should have hinges with non-removable pins or security studs.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Arcadia
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Arcadia.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Car Locksmith
On-site car key, lockout and ignition help wherever the vehicle is parked.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
- Business Lockout
Unlocking offices, storefronts, warehouses, restaurants, retail stores and commercial buildings.
Security Strike Plate Installation near Arcadia
We provide the same security strike plate installation service in the communities around Arcadia. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Sierra Madre
- Security Strike Plate Installation in Monrovia
- Security Strike Plate Installation in Temple City
- Security Strike Plate Installation in Duarte
- Security Strike Plate Installation in Bradbury
- Security Strike Plate Installation in San Marino
- Security Strike Plate Installation in Rosemead
- Security Strike Plate Installation in El Monte
- Security Strike Plate Installation in San Gabriel
- Security Strike Plate Installation in Baldwin Park
- Security Strike Plate Installation in Alhambra
- Security Strike Plate Installation in South El Monte
Security Strike Plate Installation in Arcadia: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why do I have to push my door to lock it in Arcadia?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Is there a travel charge for Arcadia?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Arcadia, so you know the cost in advance.
Can you make car keys in Arcadia?
Yes. We cut and program car keys on site anywhere in Arcadia, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Which parts of Arcadia do you serve?
All of Arcadia, including the Upper Rancho, the Lower Rancho, Santa Anita Oaks, and the Baldwin Avenue corridor, and addresses in ZIP codes 91006 and 91007.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
