Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Duarte as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Duarte, Los Angeles County, CA (91010)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Who we help in Duarte
- Reasons to call for security strike plate installation service
- Security Strike Plate Installation across Duarte
- What happens when you call
- Typical calls we receive
- What our technicians bring
- Trade terms explained
- Cost factors for security strike plate installation service
- What you can expect from us
- Advice worth knowing
- Doing it yourself versus calling a professional
- Our service standards
- Choosing a locksmith: a short checklist
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Duarte
- Security Strike Plate Installation near Duarte
- Security Strike Plate Installation in Duarte: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

A lock can only do its job if the door around it works. Hinges, latches, strike plates and frames move over time, and the lock is usually blamed for problems that begin elsewhere. Our security strike plate installation service in Duarte looks at the whole opening and fixes the cause, so the door closes with a push and locks without force.
Who we help in Duarte
Door hardware calls in Duarte come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Duarte.
Reasons to call for security strike plate installation service
If any of the following sounds familiar, security strike plate installation service is likely what you need:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Duarte
Located in Los Angeles County, Duarte is an incorporated city within our San Gabriel Valley service area. Customers anywhere in Duarte, including the Huntington Drive corridor, the City of Hope district, the foothill neighborhoods, and the Mountain Avenue corridor, can have a mobile technician sent directly to them. That includes addresses in ZIP code 91010.
Duarte is a small foothill city anchored by a nationally known medical center, where visitors and staff often need car lockout help and residents ask for straightforward rekeys and repairs.
People call us from all over Duarte, including the areas around City of Hope National Medical Center, the Duarte/City of Hope Metro station, Encanto Park, and the Route 66 corridor on Huntington Drive. A landmark or cross street helps the technician reach you quickly. Depending on where the closest technician is, the drive into Duarte follows I-210, I-605, Huntington Drive, Buena Vista Street, Mountain Avenue, and Royal Oaks Drive. You get a realistic arrival estimate when you call.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- A latch has jammed and someone is stuck in a room.
- The top corner of the door rubs the frame and the paint is wearing through.
- The deadbolt only turns if you pull the door hard toward you.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
Cost factors for security strike plate installation service
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
What you can expect from us
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.

Advice worth knowing
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Choosing a locksmith: a short checklist
- Get an itemized receipt showing labor, parts and the business details.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Duarte
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Duarte.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- High Security Locks
Locks engineered to resist picking, bumping, drilling and unauthorized key copying.
- Car Locksmith
On-site car key, lockout and ignition help wherever the vehicle is parked.
- House Lockout
Unlocking front doors, back doors, side doors, garage entry doors and interior doors, without damaging the lock whenever possible.
- Automotive Locksmith
Mobile key, lock and ignition service for cars, trucks, SUVs, vans, motorcycles and fleets.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
Security Strike Plate Installation near Duarte
We provide the same security strike plate installation service in the communities around Duarte. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Bradbury
- Security Strike Plate Installation in Monrovia
- Security Strike Plate Installation in Irwindale
- Security Strike Plate Installation in Arcadia
- Security Strike Plate Installation in Baldwin Park
- Security Strike Plate Installation in Azusa
- Security Strike Plate Installation in Sierra Madre
- Security Strike Plate Installation in Temple City
- Security Strike Plate Installation in West Covina
- Security Strike Plate Installation in El Monte
- Security Strike Plate Installation in Covina
- Security Strike Plate Installation in Glendora
Security Strike Plate Installation in Duarte: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Which parts of Duarte do you serve?
All of Duarte, including the Huntington Drive corridor, the City of Hope district, the foothill neighborhoods, and the Mountain Avenue corridor, and addresses in ZIP code 91010.
Can you make car keys in Duarte?
Yes. We cut and program car keys on site anywhere in Duarte, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Do you have a locksmith shop in Duarte?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Duarte and the rest of the San Gabriel Valley area. All work is done at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
