Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Bradbury as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Bradbury, Los Angeles County, CA (91008)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Customers we serve in Bradbury
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Bradbury
- What happens when you call
- Common situations in Bradbury
- What our technicians bring
- Trade terms explained
- Cost factors for security strike plate installation service
- Why Bradbury customers choose Big Daddy
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- Our service standards
- How to choose a locksmith you can trust
- How to prepare for the visit
- Aftercare and records
- Related locksmith services in Bradbury
- Security Strike Plate Installation near Bradbury
- Security Strike Plate Installation in Bradbury: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Bradbury deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Bradbury
Door hardware calls in Bradbury come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Bradbury.
Signs you need security strike plate installation service
These are the most common reasons customers in Bradbury ask for security strike plate installation service:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Bradbury
Located in Los Angeles County, Bradbury is an incorporated city within our San Gabriel Valley service area. We cover every part of Bradbury, including Bradbury Estates, Woodlyn Lane, the Royal Oaks corridor, and the Mount Olive area. Wherever you are in town, the technician comes to your door, driveway or parking space. Service is available throughout ZIP code 91008.
Bradbury is a tiny, largely gated city of multi-acre equestrian estates, where work typically involves estate-wide rekeys, driveway gate hardware, guest house locks and safes.
People call us from all over Bradbury, including the areas around the Bradbury Estates gate, the Royal Oaks Trail, the city’s equestrian estates, and the San Gabriel Mountain foothills. A landmark or cross street helps the technician reach you quickly. Technicians usually reach Bradbury by I-210, Royal Oaks Drive, Mount Olive Drive, Woodlyn Lane, and Lemon Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Bradbury
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The top corner of the door rubs the frame and the paint is wearing through.
- The back door swings outward and its latch is visible through the gap.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for security strike plate installation service
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Bradbury customers choose Big Daddy
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Bradbury.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.

Practical advice from our locksmiths
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Get an itemized receipt showing labor, parts and the business details.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Bradbury
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Bradbury.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- 24 Hour Locksmith
Locksmith help day or night, every day of the year.
- Key Fob Replacement
Replacing remote key fobs for cars, trucks, SUVs and vans.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Transponder Key Programming
Programming chip keys for vehicles with immobilizer systems.
Security Strike Plate Installation near Bradbury
We provide the same security strike plate installation service in the communities around Bradbury. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Duarte
- Security Strike Plate Installation in Monrovia
- Security Strike Plate Installation in Irwindale
- Security Strike Plate Installation in Arcadia
- Security Strike Plate Installation in Azusa
- Security Strike Plate Installation in Baldwin Park
- Security Strike Plate Installation in Sierra Madre
- Security Strike Plate Installation in Temple City
- Security Strike Plate Installation in West Covina
- Security Strike Plate Installation in Covina
- Security Strike Plate Installation in Glendora
- Security Strike Plate Installation in El Monte
Security Strike Plate Installation in Bradbury: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Bradbury?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Which parts of Bradbury do you serve?
All of Bradbury, including Bradbury Estates, Woodlyn Lane, the Royal Oaks corridor, and the Mount Olive area, and addresses in ZIP code 91008.
Do you have a locksmith shop in Bradbury?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Bradbury and the rest of the San Gabriel Valley area. All work is done at your location.
How long does it take a locksmith to reach me in Bradbury?
It depends on where the nearest technician is and on traffic along I-210, Royal Oaks Drive, or Mount Olive Drive. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
