Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Bell as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Bell, Los Angeles County, CA (90201)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Customers we serve in Bell
- When you need security strike plate installation service
- Security Strike Plate Installation across Bell
- How our security strike plate installation service works
- Common situations in Bell
- Equipment and hardware on the van
- Terms worth knowing
- Cost factors for security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Advice worth knowing
- Why this is a job for a locksmith
- What we commit to
- Questions to ask any locksmith
- How to prepare for the visit
- After the visit
- Related locksmith services in Bell
- Security Strike Plate Installation near Bell
- Security Strike Plate Installation in Bell: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Bell deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Bell
Door hardware calls in Bell come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Bell.
When you need security strike plate installation service
People in Bell usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Bell
Located in Los Angeles County, Bell is an incorporated city within our Gateway Cities service area. We cover every part of Bell, including the Gage Avenue corridor, the Atlantic Avenue corridor, and the Florence Avenue corridor. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 90201 ZIP code.
Bell is a compact, densely populated city of small homes, back units and apartment buildings, where landlords and families commonly ask for rekeys, deadbolts and security door locks.
Whether you are at home, at work, or stuck near the James George Bell House, Bell Community Center, Veterans Memorial Park, or the Atlantic Avenue business district, tell the dispatcher the nearest landmark and we will find you. Depending on where the closest technician is, the drive into Bell follows I-710, Atlantic Avenue, Gage Avenue, Florence Avenue, and Eastern Avenue. You get a realistic arrival estimate when you call.
How our security strike plate installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Bell
- The top corner of the door rubs the frame and the paint is wearing through.
- A previous break-in left the jamb cracked around the strike.
- The back door swings outward and its latch is visible through the gap.
- The door drifts open by itself because the latch no longer catches.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
Cost factors for security strike plate installation service
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Bell.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.

Advice worth knowing
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Get an itemized receipt showing labor, parts and the business details.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Bell
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Bell.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Chain Installation
Installing door chains or secondary security locks.
- Lost Car Key Replacement
Making a new car key when all keys are lost.
- High Security Locks
Locks engineered to resist picking, bumping, drilling and unauthorized key copying.
- Ignition Repair
Repairing ignition cylinders that are stuck, worn or will not turn.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
Security Strike Plate Installation near Bell
We provide the same security strike plate installation service in the communities around Bell. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Maywood
- Security Strike Plate Installation in Cudahy
- Security Strike Plate Installation in South Gate
- Security Strike Plate Installation in Huntington Park
- Security Strike Plate Installation in Bell Gardens
- Security Strike Plate Installation in Commerce
- Security Strike Plate Installation in Vernon
- Security Strike Plate Installation in East Los Angeles
- Security Strike Plate Installation in Lynwood
- Security Strike Plate Installation in Downey
- Security Strike Plate Installation in Montebello
- Security Strike Plate Installation in Pico Rivera
Security Strike Plate Installation in Bell: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why do I have to push my door to lock it in Bell?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you have a locksmith shop in Bell?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Bell and the rest of the Gateway Cities area. All work is done at your location.
Is there a travel charge for Bell?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Bell, so you know the cost in advance.
Are you open 24 hours in Bell?
Yes. We take calls and dispatch to Bell 24 hours a day, including weekends and holidays.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
Which areas do you cover?
We serve communities across Los Angeles County and Ventura County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
