Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Pico Rivera as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Pico Rivera, Los Angeles County, CA (90660)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Customers we serve in Pico Rivera
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Pico Rivera
- What happens when you call
- Situations we handle regularly
- Equipment and hardware on the van
- Terms worth knowing
- What affects the cost of security strike plate installation service
- Why Pico Rivera customers choose Big Daddy
- Practical advice from our locksmiths
- Why this is a job for a locksmith
- How we work on every job
- Choosing a locksmith: a short checklist
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Pico Rivera
- Security Strike Plate Installation near Pico Rivera
- Security Strike Plate Installation in Pico Rivera: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Pico Rivera deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Pico Rivera
Door hardware calls in Pico Rivera come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Pico Rivera.
Signs you need security strike plate installation service
People in Pico Rivera usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Pico Rivera
Located in Los Angeles County, Pico Rivera is an incorporated city within our Gateway Cities service area. Our security strike plate installation service reaches all of Pico Rivera, including the Whittier Boulevard corridor, the Rosemead Boulevard corridor, the Washington Boulevard corridor, and the Rivera district, as well as the streets in between. You do not need to bring anything to a shop. Service is available throughout ZIP code 90660.
Pico Rivera lies between two rivers with solid 1950s neighborhoods and major retail centers, where homeowners often replace decades-old locks and add deadbolts to side and garage doors.
If you are out and about near the Pico Rivera Sports Arena, Pico Rivera Towne Center, Smith Park, or the Rio Hondo and San Gabriel River greenways, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Pico Rivera follows I-5, I-605, Whittier Boulevard, Rosemead Boulevard, Washington Boulevard, and Slauson Avenue. You get a realistic arrival estimate when you call.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Situations we handle regularly
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
What affects the cost of security strike plate installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Pico Rivera customers choose Big Daddy
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Pico Rivera.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.

Practical advice from our locksmiths
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Out-swinging doors should have hinges with non-removable pins or security studs.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Choosing a locksmith: a short checklist
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Pico Rivera
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Pico Rivera.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Change Locks
Swapping out the locks on your doors for new ones, with new keys, in one visit.
- Storefront Lock Repair
Repairing locks on glass storefront doors, aluminum doors and commercial entryways.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
Security Strike Plate Installation near Pico Rivera
We provide the same security strike plate installation service in the communities around Pico Rivera. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Montebello
- Security Strike Plate Installation in Santa Fe Springs
- Security Strike Plate Installation in Bell Gardens
- Security Strike Plate Installation in Downey
- Security Strike Plate Installation in Whittier
- Security Strike Plate Installation in Commerce
- Security Strike Plate Installation in Maywood
- Security Strike Plate Installation in East Los Angeles
- Security Strike Plate Installation in Bell
- Security Strike Plate Installation in Cudahy
- Security Strike Plate Installation in South El Monte
- Security Strike Plate Installation in Norwalk
Security Strike Plate Installation in Pico Rivera: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why do I have to push my door to lock it in Pico Rivera?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Is there a travel charge for Pico Rivera?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Pico Rivera, so you know the cost in advance.
How long does it take a locksmith to reach me in Pico Rivera?
It depends on where the nearest technician is and on traffic along I-5, I-605, or Whittier Boulevard. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of Pico Rivera do you serve?
All of Pico Rivera, including the Whittier Boulevard corridor, the Rosemead Boulevard corridor, the Washington Boulevard corridor, and the Rivera district, and addresses in ZIP code 90660.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
