Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Fillmore as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Fillmore, Ventura County, CA (93015)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our strike plate adjustment service
- Customers we serve in Fillmore
- Reasons to call for strike plate adjustment service
- Strike Plate Adjustment across Fillmore
- What happens when you call
- Common situations in Fillmore
- What our technicians bring
- Terms worth knowing
- How strike plate adjustment service is priced
- What you can expect from us
- Practical advice from our locksmiths
- Doing it yourself versus calling a professional
- What we commit to
- Choosing a locksmith: a short checklist
- How to prepare for the visit
- Once the work is done
- Related locksmith services in Fillmore
- Strike Plate Adjustment near Fillmore
- Strike Plate Adjustment in Fillmore: frequently asked questions
About our strike plate adjustment service
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

Doors in Fillmore deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our strike plate adjustment service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Fillmore
Door hardware calls in Fillmore come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Fillmore.
Reasons to call for strike plate adjustment service
If any of the following sounds familiar, strike plate adjustment service is likely what you need:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Fillmore
Fillmore is an incorporated city in Ventura County, part of the area we cover every day. We cover every part of Fillmore, including Historic Downtown Fillmore, the Central Avenue corridor, the Sespe Creek area, and the North Fillmore neighborhoods. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 93015 ZIP code.
Fillmore is a small citrus-country town in the Santa Clara River Valley with a preserved early-1900s downtown, where farm gates, packing house locks and older home hardware are typical work.
Whether you are at home, at work, or stuck near the historic Central Avenue downtown, the Fillmore train depot and Central Park, the Fillmore Fish Hatchery, or the Sespe Creek citrus groves, tell the dispatcher the nearest landmark and we will find you. Technicians usually reach Fillmore by SR-126, SR-23, Central Avenue, Old Telegraph Road, Sespe Avenue, and Goodenough Road. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Common situations in Fillmore
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The top corner of the door rubs the frame and the paint is wearing through.
- The deadbolt only turns if you pull the door hard toward you.
- The door drifts open by itself because the latch no longer catches.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Strike plate
- The plate on the frame that receives the latch or bolt.
How strike plate adjustment service is priced
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Fillmore. The technician confirms the figure before starting.
What you can expect from us
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.

Practical advice from our locksmiths
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
What we commit to
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
Choosing a locksmith: a short checklist
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Fillmore
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Fillmore.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Emergency Locksmith
Urgent lock and key help for homes, businesses and vehicles at any hour.
- Storefront Lock Repair
Repairing locks on glass storefront doors, aluminum doors and commercial entryways.
- House Lockout
Unlocking front doors, back doors, side doors, garage entry doors and interior doors, without damaging the lock whenever possible.
Strike Plate Adjustment near Fillmore
We provide the same strike plate adjustment service in the communities around Fillmore. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Moorpark
- Strike Plate Adjustment in Santa Paula
- Strike Plate Adjustment in Simi Valley
- Strike Plate Adjustment in Camarillo
- Strike Plate Adjustment in Thousand Oaks
- Strike Plate Adjustment in Westlake Village
- Strike Plate Adjustment in Ojai
- Strike Plate Adjustment in Stevenson Ranch
- Strike Plate Adjustment in Agoura Hills
- Strike Plate Adjustment in Ventura
- Strike Plate Adjustment in Valencia
- Strike Plate Adjustment in Oxnard
Strike Plate Adjustment in Fillmore: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Fillmore?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Are you open 24 hours in Fillmore?
Yes. We take calls and dispatch to Fillmore 24 hours a day, including weekends and holidays.
Is there a travel charge for Fillmore?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Fillmore, so you know the cost in advance.
How long does it take a locksmith to reach me in Fillmore?
It depends on where the nearest technician is and on traffic along SR-126, SR-23, or Central Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
