Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Ojai as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Ojai, Ventura County, CA (93023)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our strike plate adjustment service
- Who uses this service
- When you need strike plate adjustment service
- Strike Plate Adjustment across Ojai
- How our strike plate adjustment service works
- Situations we handle regularly
- Tools, parts and hardware we carry
- Terms worth knowing
- What affects the cost of strike plate adjustment service
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Why this is a job for a locksmith
- Our service standards
- Questions to ask any locksmith
- How to prepare for the visit
- After the visit
- Related locksmith services in Ojai
- Strike Plate Adjustment near Ojai
- Strike Plate Adjustment in Ojai: frequently asked questions
About our strike plate adjustment service
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

Doors in Ojai deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our strike plate adjustment service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who uses this service
Door hardware calls in Ojai come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Ojai.
When you need strike plate adjustment service
These are the most common reasons customers in Ojai ask for strike plate adjustment service:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Ojai
Located in Ventura County, Ojai is an incorporated city within our service area. We cover every part of Ojai, including Downtown Ojai, the Arbolada, the East End, Meiners Oaks, Mira Monte, and Persimmon Hill. Wherever you are in town, the technician comes to your door, driveway or parking space. Service is available throughout ZIP code 93023.
Ojai is a valley town of Spanish Revival buildings, ranches and vacation rentals, where rental keypad locks, gate hardware for rural properties and antique lock repair all come up.
If you are out and about near Libbey Park and Libbey Bowl, the Ojai Arcade and Post Office Tower, the Ojai Valley Inn, Bart’s Books, or the Ojai Valley Trail, give us that location when you call and wait somewhere safe and visible. Technicians usually reach Ojai by SR-33, SR-150, Ojai Avenue, Ventura Avenue, Grand Avenue, and Signal Street. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
How our strike plate adjustment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Situations we handle regularly
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The deadbolt only turns if you pull the door hard toward you.
- The top corner of the door rubs the frame and the paint is wearing through.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
What affects the cost of strike plate adjustment service
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Ojai.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.

Tips to avoid problems
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Questions to ask any locksmith
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Get an itemized receipt showing labor, parts and the business details.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Ojai
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Ojai.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Commercial Locksmith
Lock, key, door hardware and access control service for offices, stores, restaurants, warehouses and multi-tenant buildings.
- Emergency Locksmith
Urgent lock and key help for homes, businesses and vehicles at any hour.
- Car Key Replacement
Replacing lost, stolen or damaged car keys.
- Panic Bar Installation
Installing panic bars, push bars and crash bars for emergency exits.
- Lock Installation
Installing new locks on doors that need added security, including exterior doors, bedroom doors, home offices, gates and garage access doors.
Strike Plate Adjustment near Ojai
We provide the same strike plate adjustment service in the communities around Ojai. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Ventura
- Strike Plate Adjustment in Santa Paula
- Strike Plate Adjustment in Oxnard
- Strike Plate Adjustment in Fillmore
- Strike Plate Adjustment in Camarillo
- Strike Plate Adjustment in Port Hueneme
- Strike Plate Adjustment in Moorpark
- Strike Plate Adjustment in Simi Valley
- Strike Plate Adjustment in Thousand Oaks
- Strike Plate Adjustment in Westlake Village
- Strike Plate Adjustment in Agoura Hills
- Strike Plate Adjustment in Stevenson Ranch
Strike Plate Adjustment in Ojai: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why do I have to push my door to lock it in Ojai?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you make car keys in Ojai?
Yes. We cut and program car keys on site anywhere in Ojai, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
How long does it take a locksmith to reach me in Ojai?
It depends on where the nearest technician is and on traffic along SR-33, SR-150, or Ojai Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Is there a travel charge for Ojai?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Ojai, so you know the cost in advance.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County, Ventura County and the Anaheim area of Orange County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
What are your hours?
We are open 24 hours a day, seven days a week, including weekends and holidays.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
