Quick answer
Strike Plate Adjustment: Adjusting strike plates so doors latch and lock properly. Big Daddy Car Key Replacement provides strike plate adjustment service in Santa Paula as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Strike Plate Adjustment
- Area
- Santa Paula, Ventura County, CA (93060)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our strike plate adjustment service
- Customers we serve in Santa Paula
- Signs you need strike plate adjustment service
- Strike Plate Adjustment across Santa Paula
- How our strike plate adjustment service works
- Common situations in Santa Paula
- Tools, parts and hardware we carry
- A short glossary
- Cost factors for strike plate adjustment service
- Why Santa Paula customers choose Big Daddy
- Advice worth knowing
- Professional service compared with doing it yourself
- How we work on every job
- Choosing a locksmith: a short checklist
- Before you call (562) 550-7206
- Once the work is done
- Related locksmith services in Santa Paula
- Strike Plate Adjustment near Santa Paula
- Strike Plate Adjustment in Santa Paula: frequently asked questions
About our strike plate adjustment service
Adjusting strike plates so doors latch and lock properly. The strike plate is the metal plate on the frame that receives the latch or bolt. If it sits a few millimetres off, the door rattles, will not latch, or the deadbolt binds. We reposition the plate, deepen the bolt pocket if it is too shallow, and secure it with long screws into the stud.

Doors in Santa Paula deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our strike plate adjustment service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Santa Paula
Door hardware calls in Santa Paula come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Santa Paula.
Signs you need strike plate adjustment service
These are the most common reasons customers in Santa Paula ask for strike plate adjustment service:
- The door rattles when closed
- The latch hits the plate instead of entering
- The deadbolt only extends partway
- Scrape marks show above or below the strike hole
Strike Plate Adjustment across Santa Paula
Located in Ventura County, Santa Paula is an incorporated city within our service area. Our strike plate adjustment service reaches all of Santa Paula, including Historic Downtown Santa Paula, the Oaks, the Harvard Boulevard corridor, the airport district, and East Area One, as well as the streets in between. You do not need to bring anything to a shop. That includes addresses in ZIP code 93060.
Santa Paula, the “Citrus Capital of the World,” has a well-preserved Main Street and Victorian and Craftsman homes, where storefront mortise locks and vintage residential hardware need knowledgeable repair.
If you are out and about near Santa Paula Airport and the Aviation Museum, the California Oil Museum, the downtown Main Street murals, the Santa Paula train depot, or Steckel Park, give us that location when you call and wait somewhere safe and visible. Depending on where the closest technician is, the drive into Santa Paula follows SR-126, SR-150, Main Street, Harvard Boulevard, Peck Road, and Telegraph Road. You get a realistic arrival estimate when you call.
How our strike plate adjustment service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Common situations in Santa Paula
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- A latch has jammed and someone is stuck in a room.
- A previous break-in left the jamb cracked around the strike.
- The deadbolt only turns if you pull the door hard toward you.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
Cost factors for strike plate adjustment service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why Santa Paula customers choose Big Daddy
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.

Advice worth knowing
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
Choosing a locksmith: a short checklist
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Get an itemized receipt showing labor, parts and the business details.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Santa Paula
Customers who need strike plate adjustment service often ask about these as well. Each can usually be handled in the same visit to Santa Paula.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Security Strike Plate Installation
Installing stronger strike plates with longer screws for added protection.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Panic Bar Installation
Installing panic bars, push bars and crash bars for emergency exits.
- Car Locksmith
On-site car key, lockout and ignition help wherever the vehicle is parked.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- Gate Lock Repair
Fixing stuck, broken, rusted or misaligned gate locks and latches.
- Car Key Replacement
Replacing lost, stolen or damaged car keys.
Strike Plate Adjustment near Santa Paula
We provide the same strike plate adjustment service in the communities around Santa Paula. See the main strike plate adjustment page or the full list of service areas.
- Strike Plate Adjustment in Fillmore
- Strike Plate Adjustment in Camarillo
- Strike Plate Adjustment in Ventura
- Strike Plate Adjustment in Moorpark
- Strike Plate Adjustment in Ojai
- Strike Plate Adjustment in Oxnard
- Strike Plate Adjustment in Port Hueneme
- Strike Plate Adjustment in Simi Valley
- Strike Plate Adjustment in Thousand Oaks
- Strike Plate Adjustment in Westlake Village
- Strike Plate Adjustment in Agoura Hills
- Strike Plate Adjustment in West Hills
Strike Plate Adjustment in Santa Paula: frequently asked questions
How do I know if my strike plate is misaligned?
Look for shiny rub marks on the plate above or below the opening, or a bolt that stops short. Those marks show exactly how far the plate needs to move.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why do I have to push my door to lock it in Santa Paula?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you have a locksmith shop in Santa Paula?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Santa Paula and the surrounding communities. All work is done at your location.
Which parts of Santa Paula do you serve?
All of Santa Paula, including Historic Downtown Santa Paula, the Oaks, the Harvard Boulevard corridor, and the airport district, and addresses in ZIP code 93060.
Can you make car keys in Santa Paula?
Yes. We cut and program car keys on site anywhere in Santa Paula, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
