Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Oxnard as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Oxnard, Ventura County, CA (93030, 93033, 93035, 93036)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation involves
- Customers we serve in Oxnard
- Signs you need security strike plate installation service
- Security Strike Plate Installation across Oxnard
- Our security strike plate installation process, step by step
- Situations we handle regularly
- What our technicians bring
- Terms worth knowing
- How security strike plate installation service is priced
- Why Oxnard customers choose Big Daddy
- Advice worth knowing
- Doing it yourself versus calling a professional
- How we work on every job
- How to choose a locksmith you can trust
- Before you call (562) 550-7206
- After the visit
- Related locksmith services in Oxnard
- Security Strike Plate Installation near Oxnard
- Security Strike Plate Installation in Oxnard: frequently asked questions
What security strike plate installation involves
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Oxnard deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Customers we serve in Oxnard
Door hardware calls in Oxnard come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Oxnard.
Signs you need security strike plate installation service
These are the most common reasons customers in Oxnard ask for security strike plate installation service:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Oxnard
Oxnard is an incorporated city in Ventura County, part of the Ventura County area we cover every day. We cover every part of Oxnard, including RiverPark, Downtown Oxnard, Silver Strand, Hollywood Beach, Mandalay Bay, La Colonia, South Oxnard, and Sea View Estates. Wherever you are in town, the technician comes to your door, driveway or parking space. We serve the 93030, 93033, 93035, and 93036 ZIP codes.
Oxnard is Ventura County’s largest city, combining a working harbor, beach neighborhoods, agricultural operations and a major auto center, so marine keys, farm equipment locks and car key programming all apply.
Whether you are at home, at work, or stuck near Channel Islands Harbor, The Collection at RiverPark, Heritage Square, the Oxnard Auto Center, or the Oxnard Transit Center, tell the dispatcher the nearest landmark and we will find you. Oxnard is served by US-101, Pacific Coast Highway, Rice Avenue, Rose Avenue, Ventura Road, and Victoria Avenue, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
Our security strike plate installation process, step by step
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Situations we handle regularly
- The deadbolt only turns if you pull the door hard toward you.
- The top corner of the door rubs the frame and the paint is wearing through.
- The door drifts open by itself because the latch no longer catches.
- A latch has jammed and someone is stuck in a room.
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
How security strike plate installation service is priced
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to Oxnard. The technician confirms the figure before starting.
Why Oxnard customers choose Big Daddy
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.

Advice worth knowing
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
How to choose a locksmith you can trust
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Get an itemized receipt showing labor, parts and the business details.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
Before you call (562) 550-7206
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
After the visit
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in Oxnard
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Oxnard.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Chain Installation
Installing door chains or secondary security locks.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Master Key System
Creating a key hierarchy where owners, managers and employees have different levels of access.
- Car Lockout
Unlocking vehicles when keys are locked inside.
- Storefront Lock Repair
Repairing locks on glass storefront doors, aluminum doors and commercial entryways.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
- Smart Lock Installation
Installing smart locks, keypad locks, Wi-Fi locks, Bluetooth locks, app-controlled locks and keyless entry systems.
Security Strike Plate Installation near Oxnard
We provide the same security strike plate installation service in the communities around Oxnard. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Port Hueneme
- Security Strike Plate Installation in Ventura
- Security Strike Plate Installation in Camarillo
- Security Strike Plate Installation in Santa Paula
- Security Strike Plate Installation in Ojai
- Security Strike Plate Installation in Moorpark
- Security Strike Plate Installation in Thousand Oaks
- Security Strike Plate Installation in Fillmore
- Security Strike Plate Installation in Westlake Village
- Security Strike Plate Installation in Simi Valley
- Security Strike Plate Installation in Agoura Hills
- Security Strike Plate Installation in Malibu
Security Strike Plate Installation in Oxnard: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why do I have to push my door to lock it in Oxnard?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
How long does it take a locksmith to reach me in Oxnard?
It depends on where the nearest technician is and on traffic along US-101, Pacific Coast Highway, or Rice Avenue. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Are you open 24 hours in Oxnard?
Yes. We take calls and dispatch to Oxnard 24 hours a day, including weekends and holidays.
Can you make car keys in Oxnard?
Yes. We cut and program car keys on site anywhere in Oxnard, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Is Big Daddy Car Key Replacement a mobile locksmith?
Yes. Our technicians travel to you throughout Los Angeles County and Ventura County. Keys are cut and programmed, and locks are opened, rekeyed, repaired and installed, at your location.
