Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Ventura as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Ventura, Ventura County, CA (93001, 93003, 93004)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Who we help in Ventura
- Reasons to call for security strike plate installation service
- Security Strike Plate Installation across Ventura
- How our security strike plate installation service works
- Typical calls we receive
- What our technicians bring
- A short glossary
- How security strike plate installation service is priced
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Why this is a job for a locksmith
- How we work on every job
- How to choose a locksmith you can trust
- How to prepare for the visit
- Aftercare and records
- Related locksmith services in Ventura
- Security Strike Plate Installation near Ventura
- Security Strike Plate Installation in Ventura: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

If you have to lift, push or slam a door to get it to lock, something is out of line. For security strike plate installation service in Ventura, call (562) 550-7206. A mobile technician diagnoses the opening, makes the repair on site and tests the door under normal use.
Who we help in Ventura
Door hardware calls in Ventura come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Ventura.
Reasons to call for security strike plate installation service
People in Ventura usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Ventura
Located in Ventura County, Ventura is an incorporated city within our service area. Our security strike plate installation service reaches all of Ventura, including Downtown Ventura, Midtown, Pierpont, the Ventura Keys, the Westside Avenue district, East Ventura, Montalvo, and Saticoy, as well as the streets in between. You do not need to bring anything to a shop. Service is available throughout ZIP codes 93001, 93003, and 93004.
Ventura, officially San Buenaventura, is the county seat, with a mission-era downtown, beach cottages in Pierpont, boat docks in the Keys and county offices, so historic, marine and commercial lock work all meet here.
People call us from all over Ventura, including the areas around Mission San Buenaventura, the Ventura Pier and Promenade, Ventura Harbor Village, the Downtown Main Street district, and Grant Park and the Serra Cross. A landmark or cross street helps the technician reach you quickly. Ventura is served by US-101, SR-126, SR-33, Main Street, Telegraph Road, and Victoria Avenue, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
How our security strike plate installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- The deadbolt only turns if you pull the door hard toward you.
- A latch has jammed and someone is stuck in a room.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The top corner of the door rubs the frame and the paint is wearing through.
What our technicians bring
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
How security strike plate installation service is priced
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- Ownership is always verified
- We check identification and proof of ownership or occupancy before opening a door, making a car key or changing a lock. It is the safeguard that stops anyone else from doing the same to your property.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.

Tips to avoid problems
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
Why this is a job for a locksmith
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
How we work on every job
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Get an itemized receipt showing labor, parts and the business details.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Ventura
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Ventura.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Chain Installation
Installing door chains or secondary security locks.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Car Lockout
Unlocking vehicles when keys are locked inside.
- Access Control Installation
Installing electronic access systems for offices, warehouses, apartment buildings and commercial facilities.
- Automotive Locksmith
Mobile key, lock and ignition service for cars, trucks, SUVs, vans, motorcycles and fleets.
- Commercial Door Hardware
Supplying and installing commercial-grade levers, pulls, hinges, closers, exit devices, strikes and protective plates.
- Door Closer Repair
Adjusting or repairing doors that slam, close too slowly, do not latch or stay open.
Security Strike Plate Installation near Ventura
We provide the same security strike plate installation service in the communities around Ventura. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Oxnard
- Security Strike Plate Installation in Port Hueneme
- Security Strike Plate Installation in Santa Paula
- Security Strike Plate Installation in Camarillo
- Security Strike Plate Installation in Ojai
- Security Strike Plate Installation in Fillmore
- Security Strike Plate Installation in Moorpark
- Security Strike Plate Installation in Thousand Oaks
- Security Strike Plate Installation in Simi Valley
- Security Strike Plate Installation in Westlake Village
- Security Strike Plate Installation in Agoura Hills
- Security Strike Plate Installation in Malibu
Security Strike Plate Installation in Ventura: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why do I have to push my door to lock it in Ventura?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Is there a travel charge for Ventura?
Any travel charge is part of the price range you are given on the phone before a technician is dispatched to Ventura, so you know the cost in advance.
How long does it take a locksmith to reach me in Ventura?
It depends on where the nearest technician is and on traffic along US-101, SR-126, or SR-33. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Are you open 24 hours in Ventura?
Yes. We take calls and dispatch to Ventura 24 hours a day, including weekends and holidays.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Can I book an appointment in advance?
Yes. Non-urgent work such as rekeying, lock installation, spare car keys and commercial projects can be scheduled for a time that suits you.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
