Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in Cerritos as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- Cerritos, Los Angeles County, CA (90703)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation involves
- Who we help in Cerritos
- Reasons to call for security strike plate installation service
- Security Strike Plate Installation across Cerritos
- What happens when you call
- Typical calls we receive
- Equipment and hardware on the van
- Trade terms explained
- Cost factors for security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Practical advice from our locksmiths
- Doing it yourself versus calling a professional
- Our service standards
- How to choose a locksmith you can trust
- How to prepare for the visit
- Aftercare and records
- Related locksmith services in Cerritos
- Security Strike Plate Installation near Cerritos
- Security Strike Plate Installation in Cerritos: frequently asked questions
What security strike plate installation involves
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in Cerritos deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who we help in Cerritos
Door hardware calls in Cerritos come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in Cerritos.
Reasons to call for security strike plate installation service
These are the most common reasons customers in Cerritos ask for security strike plate installation service:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across Cerritos
Located in Los Angeles County, Cerritos is an incorporated city within our Gateway Cities service area. Our security strike plate installation service reaches all of Cerritos, including the Cerritos Towne Center district, the Auto Square district, the neighborhoods around Cerritos Regional Park, and the Bloomfield corridor, as well as the streets in between. You do not need to bring anything to a shop. Service is available throughout ZIP code 90703.
Cerritos is home to one of the largest auto malls in the world, plus well-maintained 1970s tract neighborhoods, so car key programming and home lock upgrades are both in constant demand.
People call us from all over Cerritos, including the areas around Los Cerritos Center, Cerritos Auto Square, the Cerritos Center for the Performing Arts, and the Cerritos Library. A landmark or cross street helps the technician reach you quickly. Cerritos is served by SR-91, I-605, I-5, South Street, Bloomfield Avenue, and Studebaker Road, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
What happens when you call
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The deadbolt only turns if you pull the door hard toward you.
- A previous break-in left the jamb cracked around the strike.
- A latch has jammed and someone is stuck in a room.
- The door drifts open by itself because the latch no longer catches.
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Trade terms explained
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
Cost factors for security strike plate installation service
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Open 24 hours, every day
- Lock and key problems do not wait for business hours, and neither do we. A dispatcher answers the phone at any time of day or night, on weekends and on holidays, and sends a technician to Cerritos.

Practical advice from our locksmiths
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Get an itemized receipt showing labor, parts and the business details.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in Cerritos
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to Cerritos.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Alignment for Locks
Fixing lock issues caused by sagging doors, shifted frames or misalignment.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Chain Installation
Installing door chains or secondary security locks.
- Transponder Key Programming
Programming chip keys for vehicles with immobilizer systems.
- Smart Lock Installation
Installing smart locks, keypad locks, Wi-Fi locks, Bluetooth locks, app-controlled locks and keyless entry systems.
- Lock Replacement
Replacing old, damaged, outdated or unsecured locks with new locks.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- High Security Locks
Locks engineered to resist picking, bumping, drilling and unauthorized key copying.
Security Strike Plate Installation near Cerritos
We provide the same security strike plate installation service in the communities around Cerritos. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in Artesia
- Security Strike Plate Installation in Hawaiian Gardens
- Security Strike Plate Installation in Norwalk
- Security Strike Plate Installation in Cypress
- Security Strike Plate Installation in Bellflower
- Security Strike Plate Installation in Buena Park
- Security Strike Plate Installation in Lakewood
- Security Strike Plate Installation in La Mirada
- Security Strike Plate Installation in Stanton
- Security Strike Plate Installation in Paramount
- Security Strike Plate Installation in Santa Fe Springs
- Security Strike Plate Installation in Downey
Security Strike Plate Installation in Cerritos: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Do you have a locksmith shop in Cerritos?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout Cerritos and the rest of the Gateway Cities area. All work is done at your location.
Are you open 24 hours in Cerritos?
Yes. We take calls and dispatch to Cerritos 24 hours a day, including weekends and holidays.
How long does it take a locksmith to reach me in Cerritos?
It depends on where the nearest technician is and on traffic along SR-91, I-605, or I-5. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
Where is Big Daddy Car Key Replacement located?
Our business address is 450 W Wilken Way, Anaheim, CA 92802. Service is mobile, so the work is carried out wherever you and your vehicle or property are.
How do I get a price?
Call (562) 550-7206. Tell us what you need and where you are, and we will give you a price range for the job before sending anyone.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
