Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in La Verne as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- La Verne, Los Angeles County, CA (91750)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- About our security strike plate installation service
- Who uses this service
- Reasons to call for security strike plate installation service
- Security Strike Plate Installation across La Verne
- How our security strike plate installation service works
- Common situations in La Verne
- Equipment and hardware on the van
- Terms worth knowing
- What affects the cost of security strike plate installation service
- Why La Verne customers choose Big Daddy
- Practical advice from our locksmiths
- Professional service compared with doing it yourself
- Our service standards
- How to choose a locksmith you can trust
- How to prepare for the visit
- Aftercare and records
- Related locksmith services in La Verne
- Security Strike Plate Installation near La Verne
- Security Strike Plate Installation in La Verne: frequently asked questions
About our security strike plate installation service
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in La Verne deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who uses this service
Door hardware calls in La Verne come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in La Verne.
Reasons to call for security strike plate installation service
People in La Verne usually call us for security strike plate installation service in situations like these:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across La Verne
La Verne is an incorporated city in Los Angeles County, part of the Pomona Valley area we cover every day. We cover every part of La Verne, including Old Town La Verne, La Verne Heights, Marshall Canyon, Live Oak, and the Foothill Boulevard corridor. Wherever you are in town, the technician comes to your door, driveway or parking space. Service is available throughout ZIP code 91750.
La Verne pairs a historic Old Town and university campus with hillside estates and mobile-home communities, so the work ranges from vintage door hardware to gate locks and student car keys.
People call us from all over La Verne, including the areas around the University of La Verne, Old Town La Verne, Brackett Field Airport, Marshall Canyon Regional Park, and the neighboring Fairplex. A landmark or cross street helps the technician reach you quickly. La Verne is served by I-210, SR-57, Foothill Boulevard, Arrow Highway, D Street, and White Avenue, and our drivers know how those routes behave at different hours. We quote an arrival time based on where the nearest van actually is.
How our security strike plate installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
On arrival the technician confirms who you are and what is needed, inspects the job, and tells you the price before starting. If the situation differs from what was described on the phone, you hear the options first. Once the work is complete, you try every lock and key yourself and are given an itemized receipt.

Common situations in La Verne
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- The back door swings outward and its latch is visible through the gap.
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
Equipment and hardware on the van
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
Terms worth knowing
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
What affects the cost of security strike plate installation service
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
Prices depend on the details above, so the honest way to quote is to ask a few questions first. Call (562) 550-7206, describe the job, and you will hear a price range before anyone drives to La Verne. The technician confirms the figure before starting.
Why La Verne customers choose Big Daddy
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.
- Non-destructive methods first
- Locks are picked or bypassed and vehicles opened with purpose-made tools wherever possible. Drilling and replacement are last resorts, used only when a lock has truly failed and only with your agreement.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.

Practical advice from our locksmiths
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- If a door suddenly starts sticking, check for plumbing leaks or foundation movement.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
Professional service compared with doing it yourself
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
We keep to a consistent set of standards on every call. You hear a price range before dispatch and a confirmed price before work begins. Identification is checked, because the same care that slows a job by a minute protects your own property from someone else. Non-destructive methods come first. You try every key and lock yourself before the technician leaves, and you are given an itemized receipt.
How to choose a locksmith you can trust
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Get an itemized receipt showing labor, parts and the business details.
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
How to prepare for the visit
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Aftercare and records
Keep the receipt from your visit. It lists the hardware fitted and the work carried out, which is useful for insurance, for a landlord or homeowners association, and for anyone who works on the same locks later. Make a note of who holds each new key and where the spares are kept. If anything we worked on does not feel right in the days that follow, call (562) 550-7206 and tell us what you have noticed so it can be looked at promptly. When circumstances change, such as a new tenant, a new employee or a new vehicle, the same number reaches us at any hour.
Related locksmith services in La Verne
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to La Verne.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Chain Installation
Installing door chains or secondary security locks.
- Locksmith Near Me
A local mobile locksmith dispatched to your location across Los Angeles, Ventura and Orange County.
- Residential Locksmith
Complete lock and key service for houses, apartments, condos and rental properties.
- Rekey Locks
Resetting your existing locks to a new key so previous keys stop working, without replacing the hardware.
- 24 Hour Locksmith
Locksmith help day or night, every day of the year.
- Lock Rekey
Changing the internal pins of an existing lock so old keys no longer work. Ideal after moving in, tenant changes, lost keys or employee turnover.
Security Strike Plate Installation near La Verne
We provide the same security strike plate installation service in the communities around La Verne. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in San Dimas
- Security Strike Plate Installation in Claremont
- Security Strike Plate Installation in Pomona
- Security Strike Plate Installation in Diamond Bar
- Security Strike Plate Installation in Glendora
- Security Strike Plate Installation in Covina
- Security Strike Plate Installation in Walnut
- Security Strike Plate Installation in Azusa
- Security Strike Plate Installation in Irwindale
- Security Strike Plate Installation in West Covina
- Security Strike Plate Installation in Baldwin Park
- Security Strike Plate Installation in Rowland Heights
Security Strike Plate Installation in La Verne: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
Why do I have to push my door to lock it in La Verne?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
How long does a door adjustment take?
Most single-door alignments and strike adjustments take 30 to 60 minutes. Reinforcement kits take a little longer.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
Can you make car keys in La Verne?
Yes. We cut and program car keys on site anywhere in La Verne, including transponder keys, remote head keys and push-to-start smart keys for most makes and models.
Are you open 24 hours in La Verne?
Yes. We take calls and dispatch to La Verne 24 hours a day, including weekends and holidays.
Do you have a locksmith shop in La Verne?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout La Verne and the rest of the Pomona Valley area. All work is done at your location.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
