Quick answer
Security Strike Plate Installation: Installing stronger strike plates with longer screws for added protection. Big Daddy Car Key Replacement provides security strike plate installation service in San Dimas as a mobile service, open 24 hours. Call (562) 550-7206 for a price range and an estimated arrival time.
Last updated
- Service
- Security Strike Plate Installation
- Area
- San Dimas, Los Angeles County, CA (91773)
- Hours
- Open 24 hours, 7 days a week
- Service type
- Mobile, at your location
- Category
- Door Hardware Services
- Phone
- (562) 550-7206
On this page
- What security strike plate installation means
- Who uses this service
- Signs you need security strike plate installation service
- Security Strike Plate Installation across San Dimas
- How our security strike plate installation service works
- Typical calls we receive
- Tools, parts and hardware we carry
- A short glossary
- What affects the cost of security strike plate installation service
- Why call Big Daddy Car Key Replacement
- Tips to avoid problems
- Doing it yourself versus calling a professional
- Our service standards
- How to choose a locksmith you can trust
- What to have ready when you call
- Once the work is done
- Related locksmith services in San Dimas
- Security Strike Plate Installation near San Dimas
- Security Strike Plate Installation in San Dimas: frequently asked questions
What security strike plate installation means
Installing stronger strike plates with longer screws for added protection. The small strike plate supplied with most locks is held by short screws into thin door-jamb trim. A security strike is longer, made of heavier steel, and fastened with three-inch screws that reach the wall framing, so a kick has to break the stud, not just the trim.

Doors in San Dimas deal with settling foundations, seasonal humidity, sun-baked frames and years of daily use. Our security strike plate installation service corrects the misalignment, wear and loose hardware that make doors hard to close or lock, and adds reinforcement where a door is weaker than it should be.
Who uses this service
Door hardware calls in San Dimas come from homeowners with doors that stick or will not latch, landlords preparing units, businesses with heavily used entrances, and anyone who has had a door forced. Older buildings with settled frames and newer homes with lightly built doors both benefit from proper alignment and reinforcement.
This service is part of our door hardware services in San Dimas.
Signs you need security strike plate installation service
If any of the following sounds familiar, security strike plate installation service is likely what you need:
- Your strike plate is held by short screws
- The jamb is cracked or has been repaired before
- You are installing a new deadbolt
- You want an inexpensive, meaningful upgrade
Security Strike Plate Installation across San Dimas
Located in Los Angeles County, San Dimas is an incorporated city within our San Gabriel Valley service area. Customers anywhere in San Dimas, including Historic Downtown San Dimas, Via Verde, the Bonita Avenue corridor, and the San Dimas Canyon area, can have a mobile technician sent directly to them. That includes addresses in ZIP code 91773.
San Dimas keeps a Western-themed downtown and plenty of horse property, alongside the Via Verde hillside neighborhoods, so gate and tack-room locks sit next to standard home and business service.
If you are out and about near Raging Waters Los Angeles, Frank G. Bonelli Regional Park, Historic Downtown San Dimas, or San Dimas Canyon Park, give us that location when you call and wait somewhere safe and visible. Technicians usually reach San Dimas by I-210, SR-57, I-10, Arrow Highway, Bonita Avenue, and San Dimas Avenue. Traffic on those routes affects arrival times, which is why we give you a live estimate on the phone.
How our security strike plate installation service works
Describe the symptom
Tell us what the door does: rubs, rattles, will not latch, needs lifting to lock, or sticks at certain times of year. Symptoms point to the cause.
Inspect the whole opening
The technician checks the hinge screws, the gap around the door, the latch, the bolt, the strike plate and the frame for movement or damage.
Find the root cause
Marks on the strike plate, uneven gaps and loose hinges show whether the door has dropped, the frame has shifted, or the hardware itself has failed.
Agree the repair and price
You hear what needs adjusting, what needs replacing and what would be worth reinforcing, with prices, before work starts.
Make the repair
Hinges are re-anchored or shimmed, strikes repositioned and secured with long screws, latches replaced and bolt pockets deepened as required.
Test under real conditions
The door is closed normally, latched and locked several times. The deadbolt should extend fully without pushing or pulling on the door.
When the technician arrives, they introduce themselves, confirm the work you asked for and check your identification. They look at the lock, door or vehicle before touching it, explain what they found and confirm the price. Only then does work begin. When it is finished, you test everything yourself, and you receive an itemized receipt.

Typical calls we receive
- The back door swings outward and its latch is visible through the gap.
- A previous break-in left the jamb cracked around the strike.
- The door drifts open by itself because the latch no longer catches.
- The deadbolt only turns if you pull the door hard toward you.
- The top corner of the door rubs the frame and the paint is wearing through.
- A latch has jammed and someone is stuck in a room.
Tools, parts and hardware we carry
For door hardware work we carry replacement latches and deadlatches, adjustable and extended strike plates, heavy security strikes, jamb reinforcement kits, wrap-around door plates in common finishes and sizes, latch guards, residential and commercial hinges, hinge shims, three-inch case-hardened screws, door viewers, swing-bar guards and chains. For commercial openings we add pivot sets, continuous hinges and door closers. The right small part, fitted properly, is usually all a troublesome door needs.
A short glossary
- Deadlatch
- A latch with a small plunger that stops it being pushed back with a card once the door is closed.
- Bolt throw
- How far a deadbolt extends from the door edge. One inch is the standard for security.
- Door wrap
- A metal plate that wraps the door edge around the lock to reinforce it against splitting.
- Strike plate
- The plate on the frame that receives the latch or bolt.
- Latch guard
- A plate covering the gap at the lock so the latch cannot be reached with a pry tool.
- Latch
- The spring-loaded bolt that holds a door closed and retracts when the handle is turned.
- Shim
- A thin spacer placed behind a hinge to adjust how the door sits in its frame.
- Jamb
- The vertical part of the door frame that carries the hinges on one side and the strike on the other.
What affects the cost of security strike plate installation service
- Hardware quality
- Heavy-duty hinges, commercial closers and Grade 1 latches cost more than light residential parts and last longer.
- Reinforcement level
- A security strike is inexpensive. A full jamb shield and door wrap kit costs more and adds much more strength.
- Adjustment or replacement
- Tightening, shimming and repositioning are labor only. New latches, hinges, strikes or reinforcement plates add parts.
- Extent of damage
- A split jamb or cracked door edge from a kick-in needs reinforcement hardware and more time than a simple alignment.
- Door and frame material
- Wood is the easiest to adjust. Metal frames, aluminum storefronts and fiberglass doors need different methods and parts.
- Number of doors
- Several doors in one visit cost less per door than separate calls.
We do not publish a single flat price because every door, lock and vehicle is different. What we do is give you a price range for your specific job when you call (562) 550-7206, before a technician is sent, and confirm the price on site before work begins.
Why call Big Daddy Car Key Replacement
- A price range before we dispatch
- When you call (562) 550-7206 we ask a few questions and tell you what your type of job normally costs. If the technician finds something different on site, you hear about it before any work starts.
- One company for home, business and vehicle
- The same team handles house lockouts, storefront hardware, master key systems, safes and car keys. You do not need a different number for each kind of lock.
- Most jobs finished in one visit
- Because the common locks, cylinders, key blanks and parts are already on the van, lockouts, rekeys, installations and key replacements are normally completed the first time we come out.
- Car key specialists
- Car keys are in our name for a reason. We cut and program transponder keys, remote head keys and push-to-start smart keys for the great majority of makes, and we tell you honestly when a vehicle needs a dealer-supplied key.
- A workshop that comes to you
- Our vans carry key cutting machines, key programmers, lock stock and installation tools. Car keys are made beside the car and locks are serviced at your door, so there is no tow and no trip to a shop.
- A real, reachable business
- Big Daddy Car Key Replacement has a published address at 450 W Wilken Way, Anaheim, CA 92802, one phone number and one email address. You always know who you are dealing with.
- Plain explanations
- We explain what is wrong, what the options are and what each costs in ordinary language, and we recommend the least expensive fix that actually solves the problem.

Tips to avoid problems
- Tighten hinge screws once a year. Replace any that spin with three-inch screws into the framing.
- Replace hollow-core exterior doors. No lock makes a weak door strong.
- Out-swinging doors should have hinges with non-removable pins or security studs.
- Lubricate latches and hinges lightly once a year, and wipe away the excess.
- Look for shiny rub marks on the strike plate. They show exactly where the latch or bolt is hitting.
- Do not file the strike larger each season. Fix the alignment so the bolt enters cleanly.
- Seal the top and bottom edges of wood doors with paint so they absorb less moisture and swell less.
- A deadbolt must extend fully to be locked. If it stops short, it can be pushed back.
Doing it yourself versus calling a professional
Door adjustment is a matter of small measurements with large effects. Moving a strike two millimetres the wrong way, over-shimming a hinge or deepening a mortise carelessly can turn a sticking door into one that will not close. A locksmith reads the wear marks, corrects the cause instead of the symptom, and uses fasteners and reinforcement that actually reach the structure of the wall.
Our service standards
Every job follows the same routine. You are told the expected price range on the phone. The technician checks identification and ownership or occupancy on arrival, inspects the lock, door or vehicle, and confirms the price before starting. Locks are opened without damage wherever that is possible, and nothing is drilled or replaced without your agreement. When the work is finished you test it yourself, and you receive an itemized receipt.
How to choose a locksmith you can trust
- Ask for a price range for your specific job before anyone is sent, and confirm the price on site before work starts.
- Ask whether the lock will be picked or drilled. Standard locks rarely need drilling, and you should be told why if it is proposed.
- In California, locksmith companies are licensed by the Bureau of Security and Investigative Services. You can ask for the license number and check it on the state’s website.
- Get an itemized receipt showing labor, parts and the business details.
- Be cautious of advertised service fees that seem far too low. The final bill in those cases is often many times higher.
- Expect the technician to ask for your identification. A locksmith who opens doors without checking who is asking is a risk to everyone.
- Keep the number of a locksmith you trust in your phone, so you are not choosing one under pressure.
- Ask for the legal business name and where the company is based. A legitimate locksmith answers the phone with a name, not a generic phrase.
What to have ready when you call
- Your exact location: a street address, or a cross street and a landmark if you are in a parking lot or on the road.
- What you need help with: the type of door, lock or vehicle, and what has happened.
- For vehicles, the year, make and model, and whether you have any working key.
- A photo ID, and something that connects you to the property or vehicle, such as registration, a lease or a utility bill.
- A phone number where the technician can reach you on the way.
- Any detail that affects access: a gate code, a parking level, a guard desk or a locked lobby.
Once the work is done
Once the job is done, file the itemized receipt somewhere you will find it. It records what was fitted and what was done, which helps with insurance claims, landlord or HOA questions, and future service. Write down who has each key and where spares are stored. If a lock or key we worked on starts to feel different, call (562) 550-7206 and describe what is happening so we can look at it. And when something changes, whether that is a new tenant, a staff change or another vehicle, we are available on the same number around the clock.
Related locksmith services in San Dimas
Customers who need security strike plate installation service often ask about these as well. Each can usually be handled in the same visit to San Dimas.
- Door Chain Installation
Installing door chains or secondary security locks.
- Latch Guard Installation
Installing latch guards to protect against forced entry.
- Hinge Adjustment
Adjusting or replacing hinges so doors close correctly.
- Door Reinforcement
Adding security plates, reinforced strike plates, latch guards and door wrap plates.
- Door Viewer & Peephole Installation
Installing peepholes or door viewers for added safety.
- Door Latch Repair
Fixing latches that do not catch, stick or fail to retract.
- Door Hardware Repair
Repairing the locks, latches, strikes, hinges and closers that make a door open, close and secure properly.
- Strike Plate Adjustment
Adjusting strike plates so doors latch and lock properly.
- Door Lock Repair
Repairing lock cylinders, latches, strikes and internal mechanisms.
- Door Guard Installation
Installing flip guards, swing guards or security latches.
- Key Fob Replacement
Replacing remote key fobs for cars, trucks, SUVs and vans.
- Car Lockout
Unlocking vehicles when keys are locked inside.
- Key Duplication
Making spare keys for house doors, gates, mailboxes, padlocks, cabinets and more.
- Mobile Locksmith
A locksmith that comes directly to the customer’s location.
- 24 Hour Locksmith
Locksmith help day or night, every day of the year.
Security Strike Plate Installation near San Dimas
We provide the same security strike plate installation service in the communities around San Dimas. See the main security strike plate installation page or the full list of service areas.
- Security Strike Plate Installation in La Verne
- Security Strike Plate Installation in Glendora
- Security Strike Plate Installation in Pomona
- Security Strike Plate Installation in Covina
- Security Strike Plate Installation in Claremont
- Security Strike Plate Installation in Diamond Bar
- Security Strike Plate Installation in Azusa
- Security Strike Plate Installation in Walnut
- Security Strike Plate Installation in Irwindale
- Security Strike Plate Installation in West Covina
- Security Strike Plate Installation in Baldwin Park
- Security Strike Plate Installation in Bradbury
Security Strike Plate Installation in San Dimas: frequently asked questions
Are longer strike plate screws really worth it?
Yes. Replacing short strike screws with three-inch screws into the stud, and fitting a heavier strike, is one of the cheapest and most effective ways to resist a kick-in.
How can I make my door harder to kick in?
Install a reinforced strike plate with three-inch screws into the stud, a wrap-around plate at the lock, and long screws in the hinges. Together they resist the forces of a kick far better than standard hardware.
Can door problems be fixed without replacing the lock?
Very often. Most latching and locking complaints are alignment issues, and the existing lock works properly once the door and strike are corrected.
Can you repair a door frame after a break-in?
Yes. We fit jamb repair and reinforcement kits that restore strength to a split frame, and replace damaged locks and strikes in the same visit.
Why does my door lock fine in summer but not winter?
Wood swells and shrinks with humidity, moving the bolt relative to the strike. A proper adjustment leaves clearance for that movement.
Why do I have to push my door to lock it in San Dimas?
The bolt and the strike plate no longer line up, usually because the door has sagged on its hinges or the frame has moved. Realigning the door and resetting the strike fixes it.
Do you work on commercial doors as well?
Yes. We service aluminum storefront doors, hollow metal doors, pivots, continuous hinges, closers and exit devices.
Will the repair damage my door or paint?
We work carefully and keep changes within the existing hardware footprint wherever possible. Any new mortising is cut cleanly.
How long does it take a locksmith to reach me in San Dimas?
It depends on where the nearest technician is and on traffic along I-210, SR-57, or I-10. We give you a specific estimated arrival time when you call (562) 550-7206, not a blanket promise.
Which parts of San Dimas do you serve?
All of San Dimas, including Historic Downtown San Dimas, Via Verde, the Bonita Avenue corridor, and the San Dimas Canyon area, and addresses in ZIP code 91773.
Do you have a locksmith shop in San Dimas?
We are a mobile service. Our business address is 450 W Wilken Way, Anaheim, CA 92802, and our technicians travel to customers throughout San Dimas and the rest of the San Gabriel Valley area. All work is done at your location.
Do you only make car keys?
No. Car keys are our specialty, and we also provide residential, commercial and emergency locksmith services: lockouts, rekeying, lock installation and repair, door hardware, access control, safes and more.
How can I contact you other than by phone?
You can email sam@bigdaddycarkeyreplacement.com. For anything urgent, calling (562) 550-7206 is always the fastest route.
Which areas do you cover?
We serve communities across Los Angeles County, Ventura County and the Anaheim area of Orange County, from the San Fernando Valley and the Westside to the South Bay, the San Gabriel Valley, the Antelope Valley and Ventura County.
Do you check identification?
Yes. We verify identity and ownership or occupancy before opening locks, making vehicle keys or changing locks.
